Which SnapPad Fits Jack Foot that is 7-3/4 inches in Diameter

Question

Question:

I Have a 2021 Minnie Winnie model 31k 33ft. Long with automatic leveling system and the pads are 7 3/4 round but I’m not sure. Which pad should I order a 8 inch or 7 inch?

asked by: Nelson V

0

Expert Reply:

Hey Nelson, since your jack feet are 7-3/4 inch in diameter the correct size SnapPad would be the part # SP34FR which is the 8 inch size. The 1/4 inch difference wouldn't cause any issues and is close enough to allow for a solid fit still.

expert reply by: Jameson C

0

Nelson V.

12/6/2025

Hi James, thanks for the reply know I know which one to order!

Jameson C.

12/8/2025

@NelsonV Glad I could help!

Answer 1

To determine which SnapPad's are right for your 2017 Newmar Canyon Star Motorhome, you'll to first measure the diameter of landing gear foot; be sure to include the 'lip" in this measurement. If you have 10" landing gear feet,…

view full answer...

Answer 2

Hi Ben, The tongue weight of the trailer will definitely change as weight is added to the trailer. Tongue weight is typically about 10-15% of your GVWR so with your Transcend having a GVWR of 4,420 that would be a range of 442 - 663lbs. You'll…

view full answer...

Answer 3

We likely have a toolbox which will work with your Aluma 548 trailer although A-Frame toolboxes are not made specifically to fit certain trailers so you will need to know the amount of room you have to fit the box. I do recommend going with a plastic…

view full answer...

Answer 4

I attached a diagram showing how a breakaway switch, like part #420000, would be wired to a trailer mounted battery like the one on your Loudo dump trailer. With this type of setup you would not want to pull the breakaway switch with the trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Which SnapPad Fits Jack Foot that is 7-3/4 inches in Diameter

Product Page this Question was Asked From

Continue Researching