Recommended SnapPad Stabilizer Jack Pads for Lippert PSX2 Stabilizer Jacks

Question

Question:

Hi, will these fit on a 2020 Rockwood Mini-Lite 2507s with the PSX2 stabilizer jacks!

asked by: Eric H

0

Expert Reply:

They sure will Eric! The SnapPad SnapJack QD RV Stabilizer Jack Pads item # SN44VR are exactly what you need for the PSX2 stabilizer jacks. They're going to bolt right up to where the existing jack foot is and stay securely attached with the included hardware.

The SnapPad SnapJack QD RV Stabilizer Jack Pads item # SN44VR are sold in a quantity of four. They measure 8" wide x 8" long x 2-3/4" tall overall.

What kind of ground do you typically setup camp on?

You can add this information, along with any other questions you have, where it says Add Comment.

expert reply by: Jerred H

0

SN44VR
(click to enlarge)

Daniel C.

5/30/2026

These snap pads were very easy to install and work fantastic. They make our travel trailer much more stable.

Jerred H.

5/30/2026

@DanielC Thanks for the feedback Daniel. I appreciate you taking the time to share that.

Roger

5/30/2026

We put them on our 2023 Lance travel trailer. One of the best mods we’ve done - without a doubt. Very stable, much faster than the loose pads we were using. 2you will definitely like them.

Jerred H.

5/30/2026

@Roger Happy to hear that Roger! Thank you so much for taking the time to leave that feedback.

Gary S.

5/30/2026

We just added our Snap Pads to our 2025 EPro 20FBS. We have had them on for a couple months and love them. Saves a lot of time during setup and tear downs. Highly recommend. Enjoy!

Jerred H.

6/1/2026

@GaryS Thanks for leaving that feedback Gary! I remember we talked earlier this year. That's great the item # SN44VR pads are working so well for you. I appreciate you taking the time to come back and share your story.

Jerred H.

6/1/2026

@GaryS Thanks for leaving that feedback Gary! I remember we talked earlier this year. I'm happy to hear you got the item # SN44VR installed and their working so well for you.

Answer 1

Hello Jason, Thanks for writing in. For your 2026 Forest River R-Pod 192, you'll need the SnapPad SnapJack SJ RV Scissor Jack Pads #SN32FR for the four scissor stabilizer jacks and the SnapPad TJ Trailer Tongue Jack Pad #SN77VR for the rounded…

view full answer...

Answer 2

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 3

Hey Tom. The B&B 222 comes back to the Replacement B&B RV Twist-On Gravity Water Fill Cap With Strap item #BM56MR in black or item #BM29MR in polar white. The caps mount on the B&B RV Gravity Water Inlet Hatch item #BM76MR in black or…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Recommended SnapPad Stabilizer Jack Pads for Lippert PSX2 Stabilizer Jacks

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching