Rhino Rack Roof Rack that Fits 2010 Volkswagen Golf City

Question

Question:

Your site says this model fits the 2010 VW Golf City, but the photos show the rack being installed above the peerless window. On Golf City the doors frame the windows. This model cannot be installed on Golf City. Why does your site say it can be?

asked by: Jukius

0

Expert Reply:

Hey Jukius, we do have the Rhino Rack ROC25 roof rack part # RR56RR as a confirmed fit for your 2010 Volkswagen Golf City. This would be what I would recommend for your vehicle. What are you planning on carrying with this rack?

expert reply by: Jameson C

0

Julius

11/19/2025

Plan on carrying skis and snowboards with an attachment. Maybe a ladder. My vehicle has the bolts sticking out underneath the rubber liner above the doors. I do not see the fit kit required here for that.

Jameson C.

11/19/2025

@Julius The pictures on our site for the rack don't show the actual fit kit that comes with the rack but it does for sure have the hardware needed to attach to the fixed points your roof has. Do you have racks for the skis/boards and ladder already?

Julius

11/20/2025

@JamesonC That's a shame because I ended up ordering, "Inno Square Bar Roof Rack for Naked Roofs - Steel - Black - Qty 2 Part Number: IN45GR" based on it's compatibility with the Golf MK4 bodies that my car shares. And the images of the hardware for fixed points.

Jameson C.

11/20/2025

@Julius Where did you see that was correct fit for a 2010 Golf? I ran that vehicle through our fitguide and I don't see it listed but I see other fits like the # IN52QR.

See All (11) Replies to Julius ∨

Answer 1

The Rhino Rack roof rack #RR56RR does only fit the 5 door models and will not work with the 3 door models. Rhino Rack does have the similar aero bar rack part #RRVA118B-2, #RRRLKVA, and #DK064 as a confirmed fir for the 5 door models of the 2009…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Hey Jukius, we do have the Rhino Rack ROC25 roof rack part #RR56RR as a confirmed fit for your 2010 Volkswagen Golf City. This would be what I would recommend for your vehicle. What are you planning on carrying with this rack?

view full answer...

Answer 12

Hi Chas, The Lippert Road Armor Shock Absorbing Equalizer part #LC53CK may work for your trailer, but that will depend on what equalizer is currently on your trailer. In order to determine what equalizers would be a fit for your trailer, we'll…

view full answer...

Rhino Rack Roof Rack that Fits 2010 Volkswagen Golf City

Continue Researching