Should the Grease Bolts Be Tight on the Dexter DX7.5 Drop-N-Go Brake Actuator?

Question

Question:

The side bolts with the grease fittings, should they be tight or lose?

asked by: Robert L

0

Expert Reply:

Hey Robert. The side bolts with the grease fittings should be tight on the Dexter DX7.5 Drop-N-Go Brake Actuator item # 099-175-20. They're not holding the actuator on but you don't want the nuts backing themselves off.

What kind of trailer do you have?

expert reply by: Jerred H

0

Robert L.

9/25/2025

Wesco boat trailer

Jerred H.

9/25/2025

@RobertL Cool! Let me know if you have any additional questions.

Answer 1

Okay, so there's a number of things you'll need to convert your Keystone travel trailer from drum to disc brakes, and I'll detail how to determine that. You'll need a hub and rotor disc brake kit, though we don't have a way of…

view full answer...

Answer 2

The axle capacity is usually stamped into the centerline of the axle or placed on an information sticker in that same location. With that being said, the axle capacity is not necessary needed if you can provide me with the inner and outter bearing…

view full answer...

Answer 3

Hey Kelvin, From what I can find the Titan Model 6 brake actuators have their bolt holes almost in a straight line at the bottom of the coupler so you would have drill new holes in order to mount a new brake actuator. It also shows the Model 6 having…

view full answer...

Answer 4

Hey Patrick! Do you have drum brakes or disc brakes? Is the actuator 3-5/8" wide or is the channel tongue on your trailer that wide? I'm guessing you have a 3" wide channel tongue which is pretty standard. Do you need a coupler for a…

view full answer...

Answer 5

If you are wanting to replace the entire surge brake actuator on your Four Winns Horizon 190 boat trailer then I have exactly what you will need. I recommend using the Dexter Disc Brake Actuator part #099-175-20. This actuator works with 2"…

view full answer...

Answer 6

Hello Joel, thanks for reaching out. The mounting holes on the Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-20 are 3" apart on center

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Should the Grease Bolts Be Tight on the Dexter DX7.5 Drop-N-Go Brake Actuator?

Product Page this Question was Asked From

Continue Researching