Availability of Just Hangers of the Hanger Kit # HAP-105-205-01

Question

Question:

I’m curious if yall offer a kit with just these spring hanger and not the equalizer bar HAP-105-205-01

asked by: Trent M

0

Expert Reply:

Hey Trent, it sounds like you are looking for the Dexter Single-Axle Trailer Hanger Kit # HAP-105-00 which is just the hangers of the kit part # HAP-105-205-01 that you referenced.

expert reply by: Jameson C

0

Jameson C.

9/12/2025

Hey Trent, did the Dexter Single-Axle Trailer Hanger Kit work out for your needs? I'm asking because your experience could help others in a similar situation.

Answer 1

Since the springs part #SP-231275 are 2 inches wide the hanger kit part #HAP-105-00 that you referenced would work great.

view full answer...

Answer 2

Although we do not carry leaf springs that will work with this kit, I can tall you that the slipper springs you need for the Dexter Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 42-1/4" Axle Spacing #HAP-105-205-02 will need to be…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Availability of Just Hangers of the Hanger Kit # HAP-105-205-01

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching