Length of PF201 P and F Products Rub Rail

Question

Question:

May we assume the un-even aluminum trip items with a given dimension of 516inch tall and 1 1/2inch long are they 93 12inch in length. Really need pictures so I can see the cross section or end view.

asked by: Randall C

0

Expert Reply:

Did you mean to type 93-1/2 inches in length?

expert reply by: Jameson C

0

Jameson C.

8/7/2025

Hey, did you get the clarification you needed on the aluminum trim dimensions? If you’re still looking for a solution, I’m happy to help!

Answer 1

Hey Greg, welcome back! So this is a great question but for a Dexter 3,500-lb axle, the castle/spindle nut does not stay torqued to a specific ft-lb value. Dexter's official bearing-adjustment procedure is while rotating the hub, tighten the…

view full answer...

Answer 2

Trailer tires and wheels do not typically come balanced from the factory like what you see with standard passenger vehicle tires. This isn't usually needed for trailer tires and most car shops don't have the needed setup to properly balance…

view full answer...

Answer 3

Yes, the Dexter E-Z Lube Axles still require cleaning and repacking of the bearings every 12 months or 12,000 miles. The zerk fittings on the end of the spindle are to add new grease in between maintenance intervals but they are not designed to…

view full answer...

Answer 4

In the attached diagram the A measurement is actually the distance from the center of the spring hangers for a single axle trailer. The spring eye to spring eye measurement for your leaf springs will be slightly different. The B measurement that you…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Length of PF201 P and F Products Rub Rail

Product Page this Question was Asked From

Continue Researching