Replacement Brake Assemblies for Trailer with 10-1/4 inch Drums

Question

Question:

Looking at replacement drum breaks for my trailer ... I believe I located correct ones from this site just want to be sure ... anyway I can send you pics of what I have to be sure? My breaks measure 10 and 2 1/4 and I have hydrolic break assist...it is a titan dico model 60

asked by: Joe W

0

Expert Reply:

Hey Joe, based on what you described yes the Demco Hydraulic Trailer Brakes # 18788-87 that you referenced are correct for your trailer. This matches the size and the coupler type that you have as well.

expert reply by: Jameson C

0

Jameson C.

9/8/2025

Hey Joe, did the Demco Hydraulic Trailer Brakes work out for your trailer? I'm curious to know because it could help others with similar setups.

Answer 1

The brake assemblies are specific to the correct side of the trailer, a right hand brake assembly could not be used on the left side of the trailer. The assembly should be mounted so the magnet is at the bottom and the larger of the two brake pads is…

view full answer...

Answer 2

Hey Brent! The etrailer #AKUBRK-35-D fit 13"-15" wheels and come with a 2-year warranty. The Demco #18788-87 fit 14" or 15" wheels and come with a 1-year warranty. Outside of that, and the slight difference in cost, I would expect…

view full answer...

Answer 3

For 10 inch brakes like #AKUBRK-35-D you can use nut and lock washer set (8 each) #BRKH10B. If you want to source stainless or galvanized nuts locally then they should be 7/16"-20.

view full answer...

Answer 4

The number of leaves on a leaf spring does not dictate strength or capacity, so as you said, a 3000lb rated leaf spring (6,000lb axle capacity) can have various numbers of leaves since it is up to how the manufacture designed it. I wouldn't look…

view full answer...

Answer 5

Hello Troy, thanks for reaching out. It may be possible to add brakes to your axle, as long as your axle is equipped with a brake flange. It will look like a square plate with four holes at the base of the spindle. If no brake flange is present, then…

view full answer...

Answer 6

We do have what you need to replace the UFP HD-1377-10 hub and drum as well as add hydraulic brakes for your boat trailer. Here are the exact parts you will need: - Dexter Trailer Hub and Drum Assembly #84546UC3 - Hydraulic Trailer Brake Kit -…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Hey Tony, I would want all free-backing plates on a boat trailer if it was me as it allows you to back up the trailer easier. Basically they prevent the brakes from applying if you were ever to need to back up on a flat surface or a up a hill.…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

I'm guessing you actually have bearings #L44649 and you either mistyped or the bearing number is difficult to read. Having #L44649 as both the inner and outer is a very popular combination on 2,000 pound axles. If you need to verify to be sure…

view full answer...

Answer 11

Hi Tyler, great question. For your 3,500 lb axles, you’re going to be using the standard 10 inch by 2-1/4 inch electric drum brakes with a 4 bolt mounting pattern, which is the most common setup and makes replacement pretty straightforward. A solid,…

view full answer...

Replacement Brake Assemblies for Trailer with 10-1/4 inch Drums

Product Page this Question was Asked From

Continue Researching