What are the Hole Pattern Dimensions for the etrailer Scissor Stabilizer Jack - 24" Lift 2,500 lbs?

Question

Question:

I need the hole pattern dimensions for a scissor jack W29VV including the side to side dimension.

asked by: Bennett C

0

Expert Reply:

Hello Bennett,

Thank you so much for getting that picture to me showing exactly what measurement you needed.

Please refer to the image that I attached for the dimensions you requested for the mounting hole pattern for the etrailer Scissor Stabilizer Jack - 24" Lift - 2,500 lbs - Qty 1 # e29VV.

What kind of camper are you trying to put this on?

expert reply by: Kate F

0

Jack Mounting Hole Dimensions
(click to enlarge)

Answer 1

If you are looking to add shocks then measure using the following procedure: Compress the shock all the way (A) then mark the inner leg where the outer leg stops. Then release compression and measure the stroke (how far the shock moves) (B). Then…

view full answer...

Answer 2

I am attaching a photo of the mounting locations on the Ram Scissor Stabilizer Jack #TJSC-24 that I believe you were referencing. They are from the edges of the mounting holes but I believe your mounting hole locations would match up just fine. Let…

view full answer...

Answer 3

Most people prefer to completely replace the brake assembly instead of replacing just the brake shoe because the cost of the brake shoes is about 3/4 the cost of completely replacing the assembly and you'll typically have quite a hard time…

view full answer...

Answer 4

Hey Kyle, thanks for reaching out! The etrailer Scissor Stabilizer Jack - 24" Lift #e29VV has a variety of mounting hole positions that can be used for the mounting. You won't be using all 6 holes on each side of the bracket - just 4…

view full answer...

Answer 5

The R-Pod 189 usually comes fitted with four corner-mounted scissor jacks that bolt to the frame. We have a number of such bolt-on stabilizer jacks that are shown on the linked page. Many of these are sold as pairs but we also have single jacks too,…

view full answer...

Answer 6

The Draw-Tite Class III Max-Frame Trailer Hitch Receiver, #75082, will fit the following Ford Rangers: 1998 - 2010 Ford Ranger 1983 - 1997 Ford Ranger, All except GT models I have included a link to the installation details below. I have also…

view full answer...

Answer 7

What you need for your boat trailer is a pole tongue adapter like part #RP58393. This product is designed to work on trailers with straight tongues just like your boat trailer. I attached a picture of what it looks like installed. The best way to…

view full answer...

Answer 8

The factory trailer hitch options for a 2007 Toyota Tundra are tied into the rear bumper helping to provide extra support. This is why the factory trailer hitch cannot be replaced with an aftermarket trailer hitch as these do not tie into the bumper.…

view full answer...

Answer 9

I think I have a solution for you in the Global Link RV Entry Door Locking Latch Kit, #295-000021 for white or, #295-000019 for black. This latch kit measures 3.47" wide x 4.28" tall, fits doors that are 1-1/4" to 1-1/2" thick,…

view full answer...

Answer 10

To replace your Atwood RV Water Heater, Model #GC10A-4E, the direct replacement is the Atwood RV Water Heater - Gas and Electric - part #AT94022. This is the new version of your existing water heater, so it will have all the same features like a…

view full answer...

Answer 11

The Winntec 6000 regulator that you referenced is a low pressure regulator like what the JR part #37207-31525 you referenced. If it's a recall I'd imagine they'd replace what you have with something that would work but if not the…

view full answer...

What are the Hole Pattern Dimensions for the etrailer Scissor Stabilizer Jack - 24" Lift 2,500 lbs?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching