What Grease Seals do I Need for My Dexter 7,000 Pound Axles with PN 3251806?

Question

Question:

I have Dexter 7000Lb axles on my 5th wheel. I am getting ready to repack my bearings but not sure what seal to use. The part number on the axle is Dexter PN 3251806 12 inch never adjust. Any help would be appreciated. Thanks in advance.

asked by: Mark W

0

Expert Reply:

Hello Mark,

Thank you for the information.

I am showing that you will need the Grease Seal - Double Lip - 2.250" ID - 3.376" OD - GS-2250DL # GS-2250DL.

Getting things all geared up for a big trip? If so, where are you headed?

expert reply by: Kate F

0

Answer 1

Hey Brad, The wire torsion spring you're needing for your B&W Patriot 5th Wheel Trailer Hitch #BWRVK3255 can be picked up directly from B&W. IF you give them a call they'll be more than happy to ship you one.

view full answer...

Answer 2

Thanks for reaching out, Mark. It sounds like you are looking for the wire torsion spring and clip for the B&W Patriot 5th wheel hitch. We do not offer this part individually, but you can get one directly from B&W. If you give them a call…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

What Grease Seals do I Need for My Dexter 7,000 Pound Axles with PN 3251806?

Product Page this Question was Asked From

Continue Researching