Recommended Replacement For A PowerGear Slide Out Motor 520015-TSE

Question

Question:

Hi, is this motor a replacement for the Power Gear part 520015-TSE ?

asked by: Kim

0

Slide Out Motor 1
(click to enlarge)

Slide Out Motor 2
(click to enlarge)

Slide Out Motor 3
(click to enlarge)

Expert Reply:

Hi Kim,

The correct replacement motor for your PowerGear #520015-TSE would be the Replacement Gear Motor Assembly for Lippert Slide-Out # LC386321.

expert reply by: Kevin C

0

Jameson C.

1/27/2026

Hey Kim, how did the Replacement Gear Motor Assembly for your Power Gear setup work out? Knowing how it performed could help others looking for the same replacement.

Answer 1

It sounds like you are looking for a new motor for an RV slide out. I checked with my contact at Lippert Components, which makes the majority of OEM trailer and RV frames and slide-outs, and they do indeed have a direct replacement motor. You will…

view full answer...

Answer 2

To replace the rubber compression bumpers on a MORryde cushioned pin box you need the part #MR46DR.

view full answer...

Answer 3

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 4

The water heater that I recommend as a replacement for your Atwood G6A-7 that will give you the best bang for your buck is absolutely the tankless option water heater from Fogatti, and you can choose from either White or Black in color: - White:…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 12

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Recommended Replacement For A PowerGear Slide Out Motor 520015-TSE

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching