Availability of Bushing to Convert 3/4" Spindle to 1" Spindle
Updated 01/19/2026 | Published 08/11/2024
Products Featured in This Question
Question:
Wanted to know if there is a bushing made to convert a 3/4 trailer axle to 1 in to convert to 1 in hubs. Have an old trailer with intergrated wheel and hub. Want to convert so can pull wheel off and on without taking hub off as standard. Want to change with standard 1 in hub and separate wheel with tire without changing suspension and axle. Please let me know. Thanks
asked by: Tommy W
Expert Reply:
Hi Tommy; we don't carry a bushing/sleeve that would convert your 3/4" spindle to a 1" spindle and I don't know of anyone who makes such a thing. We also don't carry any hubs that will fit a spindle that uses # LM11949 inner and outer bearings. The only option would be to swap out the spindle with one like the # TRU94FR or replace the axle. I know you don't want to replace the axle but that is typically the best solution with older, obsolete setups.
This spindle is designed for 2k axles and has a 1-1/4" stub diameter. It uses # L44643 inner and outer bearings with a 1" inner diameter. This will allow you to use a hub like # AKIHUB-440-2-1K with a 4 on 4 or # AKIHUB-545-2-LFEZ-1K with a 5 on 4-1/2 bolt pattern. However, you will have to determine if this spindle can fit your existing axle. You will also need to take it to an axle shop for installation.
If you decide to replace the axle you will need to know the capacity and the hub face measurement (length) to find the right replacement.
Product Page this Question was Asked From
BT8 Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter
- Trailer Spindles
- Standard Spindle
- Without Flange
- L44643
- 1-1/4 Inch Diameter
- Round
- For 2000 lb Axle
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: junction block
- Search Results: bearing buddy trailer bearings races seals caps
- Search Results: 198 bearing buddy
- Search Results: tool set
- Shop: Van Windows Direct Half-Slider Van Bunk Window - Driver Side - 34" x 11"
- Shop: CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles - 4 on 4 - Pre-Greased
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2
- Shop: Timken Bearing Kit, L44643 Inner/Outer Bearings, L44610 Inner/Outer Races, 204507 Seal
- Shop: Ultimate Trailer Jack - Sidewind - 15-1/2" Lift - 1,500 lbs
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Shop: Armored Clearance and Side Marker Trailer Light - Incandescent - Steel Housing - Amber Lens
- Search Results: repair sleeve
- Q&A: How To Determine the Weight Capacity For a Trailer Axle
- Q&A: Are Trailer Axles with 3/4 inch Diameter Spindles Still Made
- Q&A: Replacement Hubs For Trailer With 3/4 Inch Outer Diameter Spindle That Is Straight
- Video: Review of TruRyde Trailer Spindles - Standard Spindle - TRU94FR
- Q&A: How Full Should Boat Trailer Hubs be Filled with Grease
- Q&A: Replacement Hub for a 3/4 Inch Diameter Straight Spindle
- Q&A: Replacement Brakes and Bearings for 1993 Mastercraft Boat Trailer
- Video: An In-Depth Look at the Replacement Race for LM11949 Bearing
- Video: Complete Breakdown of the CE Smith Grease Seals
- Video: Timken Replacement Trailer Wheel Bearing: The Breakdown
- Q&A: Does the Size of the Center Bore Matter When Selecting 5 Lug Spare Wheel/Tire for Trailer
- Search Results: 1781 inch trailer bearings races seals caps
- Search Results: marine grease
Robin H.
1/19/2026
Hey Tommy, did you end up trying the new spindle setup for your old trailer axle? Your results could really help others working with similar older hubs. Knowing what worked might guide someone else facing the same conversion challenge.