Is There a Replacement Hub For a AL-KO 7170 Trailer Hub?

Question

Question:

Looking for a AL -KO 7170 hub

asked by: Michael F

0

Expert Reply:

Unfortunately, Michael I cannot find any information on an AL-KO 7170 trailer hub. I would need for you to see what size bearings your hub uses and send me some images along with dimensions to identify the bolt pattern and any side brakes it may use if it is a drum or rotor style hub. If you are unable to find numbers on the bearings then you could use a Caliper # PTW80157 to measure your spindle.

expert reply by: Bud M

0

Identifying Bearings/Spindle
(click to enlarge)

Doug

7/16/2025

Inter race JM511910. Inter bearing JM511946. Outer race JM205110. Outer bearing JM205149. Seal 25911220. 8 lug. 5/8” lugs oil bath hub

Jerred H.

7/16/2025

@Doug Thanks for the part numbers. Those bearings and races match up to a Redline Hub 090814 that we have not carried for years.

Answer 1

The correct replacement we offer for an AL-KO 568182 or Hayes 09089324 is the Trailer Hub and Drum Assembly part #AKHD-865-7-1-EZ-K which will work with the EZ-Lube Spindles (Dexter) and UltraLube (AL-KO). I can confirm the above will fit an AL-KO…

view full answer...

Answer 2

I am sorry Beth, but we do not offer an equivalent to the AL-KO 5/8 hub assembly #568215. We do carry replacement bearings for this hub with the #TRJM511946 inner bearing and the #JM205149 outer bearing, but we do not offer any hubs that use this…

view full answer...

Answer 3

I wish there were an exact answer to your question but since there are so many variables involved in the wear of an axle it is impossible to determine the lifespan of an axle no matter if it is a torsion axle or a standard axle like part…

view full answer...

Answer 4

Yes, If you have an enclosed utility trailer, you could bolt on the spare tire carrier, #413200, to the side provided that you were to re-enforce the area where the carrier is to be mounted. You can do this by attaching wood cross braces inside the…

view full answer...

Answer 5

Hey Kevin welcome back! The Hub Bearing Kit item #BK2-100 is most likely what you'll need. The item #L68111 race is what's used on the item #L68149 bearing found on 3,500 lbs axles. Without that second bearing part number or a measurement, I…

view full answer...

Answer 6

To determine what the correct replacement hubs are for your Magic Tilt trailer there is a little bit of information that we will need. We will need to find out inner diameter of both the Inner and Outer Bearings as well as the inner diameter of the…

view full answer...

Answer 7

The Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet- 3,500 lbs #K2HR35D may fit your UFP DB-42 axle. I don't have the specs on that axle to confirm, however if your spindle has an inner bearing diameter of 1.378 inches and…

view full answer...

Answer 8

The washer part #SW1000 is 1/8 of an inch thick. The diameter of the CE Smith Wobble Roller Retainer Ring #CE10981 is 3/16 inch.

view full answer...

Answer 9

The size winch that you will need depends on a couple of different factors. I have included part of our hand winch FAQ below regarding boat winches and have linked the FAQ article for you to view. Finding the Right Capacity Winch for your Boat…

view full answer...

Answer 10

This question actually comes up quite a bit. The hitch receiver tube and safety chain plate will block the sensors located under the rear bumper in the center. However, the sensors further to the right or left will still function and allow you to…

view full answer...

Answer 11

A 7k Dexter axle should have a number 42 spindle on it which would call for the inner bearing of 25580 and outer bearing 14125A. You should not have to press the bearings or modify the spindle in any way as long as the spindle is in decent shape.…

view full answer...

Answer 12

I wasn't able to cross-reference these numbers but if you're looking for new bearings/races and seals all you need to do is note the capacity or measure. The easiest method would be to crawl under the trailer and look for the axle tag on the…

view full answer...

Is There a Replacement Hub For a AL-KO 7170 Trailer Hub?

Product Page this Question was Asked From

Continue Researching