Availability Of 10 Foot Long Bunk Boards.

Question

Question:

I am looking for 10 ft bunk boards for my boat trailer I did not see any on the website . Do you have any or can you make them for me ?

asked by: Bob

0

Expert Reply:

Hello Bob, so we may have a potential option for you, but unfortunately we do not carry any 10' long bunk boards, nor do we have the ability to custom make you one. We do have some 5' long bunk boards # CE27820, so one option would be to double up on those. Otherwise, the longest bunk board we offer is the 7' long # CE27845.

expert reply by: Jesse M

0

Answer 1

I can certainly understand not wanting to have to connect 2 five-foot carpeted bunk rails like #CE27820 to get the 10 foot bunks you need. We don't offer them in the 10' length because the shipping costs would be more expensive than the bunks…

view full answer...

Answer 2

I recommend attaching the carpet to your boards using staples. If you wrap the carpet around the board and only staple the carpet on the sides or back of the board, the staples will not scratch the hull of your boat.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Availability Of 10 Foot Long Bunk Boards.

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching