Do the Aluminum 2-Step Scissor Steps Come with a Mounting Bracket

Question

Question:

Do I need to purchase attachment for trailer to hook the steps to or does it come with a set of stairs?

asked by: Billie

1

Helpful Expert Reply:

The mounting bracket is built into the aluminum scissor steps # AS02 so you would not need to purchase a separate bracket. It also includes the mounting hardware.

expert reply by: Michael H

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 3

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 6

Hey Bruce! The SoftStartRV Soft Start #SSR54FR is what you need for your 13K Btu Furrion Chill HE AC unit. This is a universal kit so while it won't be plug and play, it will still work with your Furrion. What's the driving force pushing you…

view full answer...

Answer 7

The Brophy Stake Pocket Mounted Camper Tie-Downs #TDSF feature a shank design that isn't compatible with stake pockets on any truck starting with the 2011 model years. This means it won't be a good option for your 2011 Chevy Silverado. For…

view full answer...

Answer 8

Great question! The All Terrain Landing Gear for RV Scissor Steps, #TLA8000, work with most factory scissor steps. Many steps like Brophy Scissor Steps #AS23 use rivets. You are correct - the rivets will need to be drilled out using a 1/4" drill…

view full answer...

Answer 9

If you check out the install picture I attached for the #AS23 you can see where it normally installs at the rear of a camper that is installed on a truck. Without seeing your setup it's hard to be more specific but there should be a spot on the…

view full answer...

Answer 10

The Brophy Camper Scissor Steps #AS24 that you referenced is designed to get removed when travelling. So the bracket would install on the camper under the door permanently and then you'd mount the steps to them when you are parked as needed. To…

view full answer...

Answer 11

I took a look at each of the scissor steps we carry and there are not any available that have the range of 18" to 26" you are looking for. You are not going to want to use the Brophy Camper Scissor Steps #AS23, which have a range of…

view full answer...

Answer 12

To add an in bed 7-way to your 2023 Ram 2500 you will want the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness item #41157. This harness puts a 7-way connector in the bed of your truck and allows you to keep the one on your bumper.…

view full answer...

Do the Aluminum 2-Step Scissor Steps Come with a Mounting Bracket

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching