Will Roadmaster Comfort Ride Kit Work with MORryde CRE3000 Kit

Question

Question:

Does the Roadmaster kit work with the CRE3000 suspension system?

asked by: Joe S

0

Expert Reply:

Hey Joe, yes the Roadmaster Comfort Ride part # RM-2460 will work with the MORryde CRE3000 cushioned equalizer like the part # MR87ZR.

expert reply by: Jameson C

0

Answer 1

Yes, the Roadmaster Comfort Ride Shock Absorbers #RM-2460 will fit your 2022 Cherokee Arctic Wolf. This kit will work on any tandem axle trailer with 3" round tube leaf spring axles. These are typically rated between 5,200 and 7,000 lbs, but a…

view full answer...

Answer 2

We do indeed have the exact bearing kit you need for your Lippert 5,100 lb axle with the part #BK3-300.

view full answer...

Answer 3

We can get you a more comfortable ride, though the Road Armor equalizers truthfully won't do the job as an upgrade over the CRE3000 MORryde Rubber Equalizers like #MR87ZR or #MR27ZR, they would just be replacing one upgraded equalizer with…

view full answer...

Answer 4

I do have an option for you but the Lippert Components Bolt-On Shock Kit like part #LC281281 is designed for use on overslung axles (leaf springs over axle) only. Therefore, it should not be used with the underslung (leaf springs under axle) axles…

view full answer...

Answer 5

Based on the information you gave me you have a couple options for shock absorbers for your 5th wheel trailer. If you 5th wheel has 3" axles you are going to want the Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers item #RM-2460…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Will Roadmaster Comfort Ride Kit Work with MORryde CRE3000 Kit

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching