Are The Dexter Nev-R-Adjust Trailer Brakes Compatible With Lippert Hub/Drums on 2020 GD Solitude 380

Question

Question:

I need to replace brakes on my 2020 Grand Design 380FL Fifth Wheel. Ive got two items in my cart: Dexter Nev-R-Adjust Electric Trailer Brakes - 12 - Left/Right Hand Assemblies - 7K - 23-464-465 Trailer Hub and Drum Assembly - 7,000-lb Axles - 12 Diameter - 8 on 6-1/2 - Pre-Greased - LC53UD Questiont 1: I want to make sure this fits the mounting flange. I havent taken the hub off to check existing ones but it is stock 2020 380FL. Also used 380FL as the filter. Question 2: The Lippert Hub and drum in the description state the grease seal is not provided but they are pregreased so that statement I blelive is incorrect. Can you confirm. I know the other components like grease cap, wheel bolts, washer ect would not be included. Question 3: I want to make sure the brake and hub/drum I ed are compatible. Thanks

asked by: Glenn B

0

Expert Reply:

For your 1st question, yes the Dexter Nev-R-Adjust Electric Trailer Brakes # 23-464-465 are going to fit the 5 bolt mounting flange on your 7,000lb axle for your 2020 Grand Design Solitude 380FL.

For your 2nd question, yes the Trailer Hub and Drum Assembly # LC53UD will include the grease seal like you see in the pics. I have sent an update to have this corrected.

And finally for your 3rd question both these parts are going to be compatible with each other. These parts do conform to the standards for a 12" x 2" brake system.

expert reply by: Bud M

0

Answer 1

Hello Brian, thanks for reaching out. Our records show the Lippert V000448334 is a standard 7,000 lb axle that uses the #25580 (1.75" ID) inner bearing and 02475 (1.25" ID) outer bearing. I do suggest you remove a hub and confirm this is…

view full answer...

Answer 2

If you already have brake drums you will not have to replace them unless they are damaged or became overheated and have discoloration on the inside armature surface where the magnet rides, grooves in the armature surface, or severe wear where the…

view full answer...

Answer 3

Dexter brand trailer axle components are considered by most people to be the highest quality around. Whenever possible I recommend them over the other brands. For 12 inch diameter Dexter brake assemblies that are self-adjusting the Dexter kit part…

view full answer...

Answer 4

I have attached for you below the brake adjustment procedure for Lippert self-adjusting braking assemblies. 1. Jack up coach and secure on adequate capacity jack stands. Follow coach manufacturer’s recommendations for lifting and supporting the…

view full answer...

Answer 5

You will have no problem using a Dexter brake assembly on a Lippert 7K axle. We have installed several Dexter brake assemblies on Lippert axles at our shop. Lippert and Dexter use the same standard mounting pattern and brake sizes. If you want…

view full answer...

Answer 6

You're not going to have any problems mixing Dexter and Lippert components on trailer axles over 10k-lbs in the same manner as below 10k-lbs as long as the measurements on the replacement parts are the same- i.e. bearing sizes are the same, etc..…

view full answer...

Answer 7

The numbers you listed do not reference any of the parts that we carry but we can still help you get the replacement parts you need. In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of…

view full answer...

Answer 8

Thanks for the photo, and you are correct, you do indeed have a Dexter 7,000 lb axle, and are also correct regarding the shoes and magnets for Dexter 7k electric brakes, the Replacement Shoe #DX28FR and Replacement Magnet #BP01-225. That said,…

view full answer...

Answer 9

The Trailer Hub and Drum Assembly #AKHD-865-7-2-K is the same as the Assembly #AKHD-865-7-1-K you found but with 1/2" wheel studs versus the 9/16". We also have the Assembly #AKHD-865-7-2-EZ-K if you need the EZ Lube grease cap to access…

view full answer...

Answer 10

Hello William, thanks for reaching out, and for providing all of that info for your axle. Your Lippert 7K axle uses a 25580 inner bearing, a 14125A outer bearing, and a 122088 grease seal - all of which can be found in the bearing kit #BK3-200. Here…

view full answer...

Answer 11

Sure can, and the correct replacement hub and drum for your trailer with a Lippert 7,000 lb axle and 8 on 6-1/2" bolt pattern is the following: - Trailer Hub and Drum Assembly - 7,000-lb Axles #LC53UD

view full answer...

Answer 12

I reached out to Lippert and the correct hub and drum assembly for your Dutchman Voltage 3200 is the Trailer Hub and Drum Assembly - 7,000-lb Axles - 12" Diameter - 8 on 6-1/2 - Pre-Greased #LC53UD. This hub has 1/2" diameter x 1-5/16"…

view full answer...

Are The Dexter Nev-R-Adjust Trailer Brakes Compatible With Lippert Hub/Drums on 2020 GD Solitude 380

Product Page this Question was Asked From

Continue Researching