Rear Torklift Camper Tie Down for 2008 Chevy Silverado 3500 with Curt Hitch

Question

Question:

What rear camper mounts fit this hitch if I have a 2008 Chevy Silverado 3500 Dually?

asked by: Kaela

0

Expert Reply:

It sounds like you are looking for a rear set of camper tie downs for your 2008 Chevy Silverado 3500 dually with the Curt hitch part # C15703. For that we have the Torklift set part # TLR3501 which I confirmed with Torklift as a fit.

expert reply by: Jameson C

0

Answer 1

The correct rear camper tie-down for your 2007 Chevy Silverado Classic 3500 long bed is the TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear #TLR3501. The other thing you may need, since you have a dually, is the TorkLift Camper Anchor…

view full answer...

Answer 2

The Torklift hitch part #TLC1205 is the hitch you'd need for your 2007 GMC Sierra 2500HD long bed as the #TLC1204 only fits the short bed trucks.

view full answer...

Answer 3

For an extension as long as you'd need to have a 2-1/2 inch hitch installed so that you could use the hitch extender part #RP45292 which can be trimmed down to 24 inches. If you were in need of a 2-1/2 inch hitch then you'd need the part…

view full answer...

Answer 4

The only other part that comes in the package of your TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear #TLR3501 apart from the parts you mentioned is the metal pin/clip that attaches the tie-down shank into the receiver shank. I went ahead and…

view full answer...

Answer 5

I'm not 100 percent certain about the exact measurement you are looking for; is it the vertical measurement of the bolt hole on the frame brackets to the hitch tube itself or the horizontal measurement from the bolt hole to the rear of the hitch…

view full answer...

Answer 6

I had our warehouse measure the Curt Trailer Hitch Receiver #C15703 you were looking at, and has an overall width of 40-5/8", overall length of 29". The distance between the vertical mounting holes is 14-1/2" center to center, and the…

view full answer...

Answer 7

Curt Trailer Hitch Receiver #C15703 hangs pretty low on a 2005 Chevy Silverado 2500. From the bottom of the bumper to the top of the hitch receiver it is approximately 4 inches. I have included a picture showing the gap. A similar hitch, #C15302,…

view full answer...

Answer 8

The #TLC3205 you have now is only designed to work with the factory hitch. Whether it is the #DT45517, a Curt hitch, or even a TorkLift hitch you will need a different rear tie-down. The correct rear tie-down for a 2002 Silverado 2500 without a board…

view full answer...

Answer 9

For your 2004 GMC Sierra 2500HD we have the Draw Tite part #41944 which is a Class V confirmed as a fit for your truck once you remove the factory hitch. This will also work with your front Torklift tie down #TLC2205 but you'll need to go with a…

view full answer...

Answer 10

It looks like the TorkLift tie downs for your old 2004 GMC Sierra 2500 long bed were #TLC2204 for the front and #TLR3503, #TLR3504, #TLC3206, or #TLR3501 for the rear. The 2015 GMC Sierra 3500 Crew Cab long bed uses #TLC2220A for the front and…

view full answer...

Answer 11

If the tube step on your 2006 Chevy Silverado 2500 short bed is only under the cab of the truck and no part of it is attached beyond the back of the cab then you would look at the tie downs for models without a board or step under the truck bed and…

view full answer...

Answer 12

Ground clearance is generally not a problem on full size trucks like your 2007 Chevy Silverado 3500. With that said the 2-1/2 inch hitches for the truck do hang fairly low. The Draw-Tite hitches #DT45519 and #DT45517 fit a little tighter to the rear…

view full answer...

Rear Torklift Camper Tie Down for 2008 Chevy Silverado 3500 with Curt Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching