Replacement For Grease Seal With 1.5 Inch Inner Diameter and 2.33 Inch Outer Diameter

Question

Question:

I was wondering if you had double lip grease seals that would replace Dexter Marine #81312. These are trailer seals that measure 1.5 X 2.31 with 1.25 inner bearings. Thanks for any info.

asked by: Douglas P

0

Expert Reply:

We have a grease seal with a 1.5" inner diameter and 2.33" outer diameter, but it is a single lip seal, the Timken Grease Seal # TMK89ZR.

expert reply by: Kyle S

0

Answer 1

It sounds like the remains of a double lip seal. Was it like a rubber o-ring with a metal spring around it? You are going to have to replace the seal so I would just disregard the sleeve. It would go on the outside of the rubber lip though. I…

view full answer...

Answer 2

We do have the exact bearings, races, and grease seal you need for your 4,400 lb Dexter axle, and while there isn't a single kit with the parts, you can get them all individually. What you will need are the following: Bearings #L68149 and…

view full answer...

Answer 3

The Timbren Heavy-Duty Axle-Less Trailer Suspension - 4" Lift Spindle - Off-Road Tires - 3,500 lbs #ASR35HDS02 is compatible with I-beam frames and in tandem axle configuration. Due to the Aluminum frame, I recommend putting a thin rubber pad…

view full answer...

Answer 4

The big things we are looking for on the label are the weight capacity, hub face (HF) length, and the spring center (SC) distance. Your axle is a 4,400 lb 85" HF and 68-1/2" CS Dexter axle. I will tell you up front that we do not carry a…

view full answer...

Answer 5

We do have the exact bearings, races, and grease seal you need for your 4,400 lb Dexter axle, and while there isn't a single kit with the parts, you can get them all individually. What you will need are the following: Bearings #L68149 and…

view full answer...

Answer 6

On Dexter axles manufactured after April 2001 you will be able to find the serial number stamped on the rear portion of the axle tube approximately 18" from the passenger side hub. Depending on the condition of the axle you may need some chalk…

view full answer...

Answer 7

It sounds like the seals have failed and the grease from the bearings has come out during travel. Also it is possible that if you have an EZ lube axle with a grease zerk at the end to add grease but use a single lip seal, the pressure can blow out…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement For Grease Seal With 1.5 Inch Inner Diameter and 2.33 Inch Outer Diameter

Product Page this Question was Asked From

Continue Researching