Replacement Brake Assemblies for Dexter Axle 12" Free Backing Hydraulic Brakes

Question

Question:

Would Item # AKUBRK-7R be a direct replacement for 023-343-00 brake assembly. If it is, what would be the part number for the same assembly for the left side?

asked by: Frank

0

Expert Reply:

To replace the Dexter Axle 023-343-00 brake assemblies on your trailer you need the 12" Hydraulic Brake Kit # AKFBBRK-7 - this includes both the left and right side assemblies.

Attached is an installation video for you to check out!

expert reply by: Jon G

0

Answer 1

Hi Joe, For the Dexter Hydraulic Trailer Brake - Right Hand #DX69CR you'll need part #bp04-162. If you need the left hand assembly #DX79CR shoes as well then you would need part #bp04-164.

view full answer...

Answer 2

Hey Tom thanks for your questions. To answer your first question, yes, you can use the #AKFBBRK-7 or the #23-342-343 free backing hydraulic brake assemblies on your dump trailer. All of these use the same standard 12" x 2" brake shoes. If…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Replacement Brake Assemblies for Dexter Axle 12" Free Backing Hydraulic Brakes

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching