Recommended Rear Camper Tie Downs for a 2017 Ford F-250 w/out Board or Steps

Question

Question:

Will this item fit my 2017 f250 truck bumper

asked by: Phillip C

0

Expert Reply:

The HappiJac Rear Tie-Down - Qty 1 item # LC182866 will fit your 2017 Ford F-250's stock bumper but you will have to drill a hole in it. I have linked a review video below.

A way better option to secure an in bed camper is to use the TorkLift Custom Frame-Mounted Camper Tie-Downs item # TLF3008. These attach directly to your frame and require no drilling that will eventually rust out your bumper like the Happijac. The tie-down inserts can be easily removed from the frame-mounted receiver brackets with included pins to leave you with your stock appearance when not using them.

expert reply by: Jerred H

0

Answer 1

The support braces in the HappiJac Truck-Mounted Camper Tie-Downs #LC182860 are going to attach to the cross frame to provide support for the anchors which will bolt through the bed wall and into the braces. The rear anchors will bolt through the…

view full answer...

Answer 2

I'd be more than happy to help you out! Attached is a wiring diagram for the Superwinch LT4000 ATV Winch #SW1140220. We don't have the instructions available as a download, but when I reached out to my contact at Superwinch they were able to…

view full answer...

Answer 3

In regards to HappiJac Truck-Mounted Camper Tie-Downs like part #LC182908-182928, the front tie-down installs inside the bed on the front panel directly behind the cab. The rear tie-down then mounts to the bumper. They will not require removal of the…

view full answer...

Answer 4

The correct front anchor plate for the HappiJack system that would fit your 2015 Ford F-350 is the part #LC182876 actually.

view full answer...

Answer 5

Unfortunately we do not have a video of the HappiJac Truck-Mounted Camper Tie-Downs #LC184089 being installed. The Rear anchors are installed in the end of the bumper. There is no precise mounting location since a variety of bumpers may be installed.…

view full answer...

Answer 6

Hey Jon, thank you so much for all of that information! We've got two options for your 2019 GMC Sierra 3500. If you have the factory running boards that run wheel to wheel you're going to be limited to the universal tie downs item #HSAB.…

view full answer...

Answer 7

Thanks for the picture of your compartment latch. It looks like a standard RV baggage door slam latch so what you'd need for a replacement would be the part #295-000078 and you'd be set.

view full answer...

Answer 8

Yes they sure will; I checked with HappiJac and the correct fit for your 2017 Ram 3500 long bed dually is the part number you referenced: - HappiJac Truck-Mounted Camper Tie-Downs #LC236326-205221 The other thing you will need with these tie-downs…

view full answer...

Answer 9

I attached a diagram that shows how most 7-way rounds like the #PK11720 that you referenced will get wired up. As long as you got yours wired up correctly and your trailer taillights and brakes are functioning correctly that's all that should…

view full answer...

Answer 10

Hey Eric, The hitch extenders that we currently offer for a 2-1/2" receiver tube opening unfortunately max out at 6,000lbs GTW and wouldn't be capable of towing the trailer. You're most likely going to need to upgrade to a TorkLift…

view full answer...

Recommended Rear Camper Tie Downs for a 2017 Ford F-250 w/out Board or Steps

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching