Mounting Bolt Pattern and Center Hole Diameter For Dexter Trailer Brake Assemblies 23-248 and 23-429
Updated 08/11/2026 | Published 08/10/2022 >
Products Featured in This Question
Question:
What is the diameter of the center hole on the # 23-429, and 23-428 brake assembly? I am trying to replace my 23-369 and 23-370 brakes with a 9 hole mounting plates? Any information or ideas to repair or replace my brakes without replacing my axels would be greatly appreciated. Thank you
asked by: Joel F
Expert Reply:
The Dexter Electric Trailer Brake Assembly # 23-429 & # 23-428 have a center opening of 3-7/8" for fitting on the axle tube. It will mount to bolt holes that are 3-5/8" spread left to right and 4-3/8" top to bottom. I have included images below with both measurements to help you identify the fitment. We also have them as a Set # 23-428-429 since you will will being replacing them on multiple axles. If these will not fit your current axles please let me know your mounting pattern and the center hole diameter required.
Product Page this Question was Asked From
Dexter Electric Trailer Brake Assembly - 12-1/4" - Right Hand - 7,200 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- RH
- 7200 lbs
- Brake Assembly
- Manual Adjust
- 12-1/4 x 2-1/2 Inch Drum
- Dexter
more information >
Continue Researching
- Shop: etrailer Electric Trailer Brakes w/ Dust Shields - Self-Adjusting - 12-1/4" - Left/Right - 8K
- Shop: Easy Grease Trailer Hub and Drum Assembly for 8K Axles - 12-1/4" Diameter - 8 on 6-1/2
- Shop: BulletProof Hitches 2-Ball Mount for 2-1/2" Hitch - 5-1/4" Drop, 5" Rise - 36,000 lbs
- Shop: Demco Hydraulic Brake Actuator - Drum - Primed - 12" Adjustable Channel Down - 12,500 lbs
- Q&A: Electric Brakes for Rockwell 8,000 lb Torsion Axles
- Q&A: Hub And Drum Replacement for 90865 Rockwell Hub and Drum
- Search Results: 8k drum
- Shop: BulletProof Hitches 2-Ball Mount for 2-1/2" Hitch - 13-1/4" Drop, 13" Rise - 36K
- Shop: Demco Trailer Coupler - Cast - Adjustable Channel - eZ-Latch - Black - 2-5/16" Ball - 21K
- Shop: Gen-Y Torsion Pintle Hook Mounting Plate for 2-1/2" Hitches - 16 Hole - 21K
- Search Results: trailer fenders
- Search Results: steel fenders
- Shop: Trailer Wiring
- Q&A: Do I Need a Load Resistor When Upgrading Trailer Lights to LEDs?
- Q&A: Troubleshooting No Trailer Connected Issue with Factory Integrated Brake Controller
- Video: What to Know About the Adapter Module for BrakeRite Electric Over Hydraulic Actuator
- Shop: Gooseneck Hitch
- Search Results: 3 16 brake hose
- Q&A: Electric Over Hydraulic Adapter Module For a 2024 Chevrolet Silverado 2500HD
- Q&A: Tires for a Tandem Axle Gooseneck Trailer with 25,900 lb GVWR
- Search Results: b & w hitch
- Search Results: trailer jack
- Search Results: gooseneck hitch trailer safety chains
- Q&A: Recommended AC System to Replace Two Dometic Duo-Therm AC Units Controlled by the Same Thermostat
- Article: Most Popular Wheel Bearings
- Article: How (and Where) to Connect an RV Propane Grill
- Article: How to Charge a Dump Trailer Battery
- Article: Spring Towing Readiness Checklist
- Article: How to Choose the Right Trailer Hitch Class
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)




Steve
8/11/2026
Are sure that 4-3/8 isn't supposed to be 3-3/8? Thanks