Recommended Hitch and Wiring Harness for a 2017 Honda CR-V Touring
Updated 08/04/2022 | Published 08/03/2022
Products Featured in This Question
Question:
Hello, Would like a class III 2 hitch for a 2017 Honda CRV Touring with foot activated lift gate sensor. Draw-Tite DT79MR seems right but not sure about Touring model. Also wiring kit. Thanks.
asked by: Joe B
Expert Reply:
We do have a hitch for the Touring model of the 2017 Honda CR-V. It is the etrailer Trailer Hitch item # e98848. This is the only hitch confirmed to fit the Touring model. As far as the foot activated lift gate sensor is concerned there is a relocation kit from Honda. Most of the time there is a sweet spot a few inches to the left and or right of the 2" x 2" receiver that allows the hands free lift gate to work properly. If you are unable to get yours to work you will need to go to your local dealership to get the relocation kit from Honda as that is not available in the aftermarket.
For a wiring harness you will want the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # 118741. This custom-fit T-One connector plugs into your Honda's wiring harness, which is located in your rear cargo area, behind the driver's-side interior trim panel. This will provide you with a 4-flat connector that will allow you to control your trailer or accessories lighting functions.
To round out your towing setup I recommend the Curt Towing Starter Kit for 2" Hitches item # C45534. This towing kit will provide you with a 2" ball and a fixed ball mount with a 3/4" rise and 2" drop. It also includes a hitch pin and clip, hitch receiver lock with keys, hitch cover, and a storage case.
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Article: My Trailer Hitch Doesn't Fit
- Article: Trailer Wiring Diagrams
- Video: Setting up the Draw-Tite Max-Frame Trailer Hitch Receiver on your 2019 Acura RDX
- Video: Feature Review Replacement Hardware Kit for Trailer Hitches
- Video: Curt Mounting Bracket for 4-Pole Flat Trailer Connector Review
- Video: Set up: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector on a 2020 Acura RDX
- Video: Installation Guide for the Draw-Tite Max-Frame Trailer Hitch Receiver on a 2018 Honda CR-V
- Video: Curt No-Drill Bracket Review
- Video: Best 2018 Honda CR-V Trailer Wiring Options
- Shop: Rubber Tube Cover 1-1/4"
- Shop: etrailer Rubber Hitch Cover for 2" Trailer Hitches - Qty 1
- Shop: Draw-Tite Logo Rubber Hitch Cover for 2" Trailer Hitches
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers
- Shop: Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Q&A: Does Rear Bumper/Fascia of 2019 Acura RDX get Trimmed to Install Trailer Hitch
- Q&A: If OEM Cutout Fascia Piece Needed When Installing Draw-Tite Trailer Hitch on a 2019 Acura RDX
- Q&A: Does the Exhaust Have to Be Lowered to Install the Draw-Tite Hitch 76268 on a 2019 Acura RDX
- Q&A: What Vehicles Does Draw Tite Hitch part # 76286 Fit
- Q&A: Removal of Rubber Isolator to Install Draw-Tite Trailer Hitch on 2020 Acura RDX
- Q&A: Does the Draw-Tite Hitch for a 2019 Acura RDX Stick Out Past the Bumper
- Q&A: Pinhole Measurement from Front and Rear of the Draw-Tite # 76268
- Article: Trailer Hitch Receiver Sizes
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
- Article: Hitch Adapters and Extenders
on Trailer Hitch
