If OEM Cutout Fascia Piece Needed When Installing Draw-Tite Trailer Hitch on a 2019 Acura RDX
Published 02/22/2019
Question:
You just listed for sale trailer hitch 76268 which has a 2 inch receiver for my 2019 Acura RDX tech package. The Acura factory hitch, is only available in a 1 1/4 inch receiver but requires a replacement Acura panel under the bumper to fit the factory hitch but the end result is a very neat installation. Do you have a picture of your 76268 mounted on a 2019 RDX I could look? Do you know if I should obtain install this Acura panel Part Number: 08L92-TJB-200B with your hitch to make it fit best?
asked by: Craig R
Expert Reply:
We personally don't have any photos as of yet (February 2019) as we haven't had a chance to install the Draw-Tite # 76268 on a 2019 Acura RDX but I do have a picture from the installation instructions which I have attached for you to check out.
Since the Draw-Tite receiver sits under that rear bumper fascia it looks like you wouldn't need the extra fascia piece that Acura recommend for their OEM trailer hitch. Although this receiver won't look quite as clean as the OEM hitch the tradeoff is that you get the Class III 2" receiver. The benefit to this is that you get a wider variety of accessories that you can use with it.
If you let me know what you would be using the trailer hitch for I can make additional recommendations if necessary.
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Trailer Wiring
- Shop: Base Plate for Tow Bar
- Article: Trailer Wiring Diagrams
- Article: My Trailer Hitch Doesn't Fit
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Video: Setting up the Draw-Tite Max-Frame Trailer Hitch Receiver on your 2019 Acura RDX
- Shop: etrailer Rubber Hitch Cover for 2" Trailer Hitches - Qty 1
- Shop: Rubber Tube Cover 1-1/4"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Draw-Tite Logo Rubber Hitch Cover for 2" Trailer Hitches
- Shop: Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers
- Shop: Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Video: Set up: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector on a 2020 Acura RDX
- Video: Feature Review Replacement Hardware Kit for Trailer Hitches
- Video: Ultimate Overview of the CR Brophy Hitch Extender for 1-1/4" Hitch Receivers
- Video: Best 2018 Honda CR-V Trailer Wiring Options
- Video: Curt Mounting Bracket for 4-Pole Flat Trailer Connector Review
- Video: Installation Guide for the Draw-Tite Max-Frame Trailer Hitch Receiver on a 2018 Honda CR-V
- Q&A: Does Rear Bumper/Fascia of 2019 Acura RDX get Trimmed to Install Trailer Hitch
- Q&A: Does the Draw-Tite Hitch for a 2019 Acura RDX Stick Out Past the Bumper
- Q&A: Removal of Rubber Isolator to Install Draw-Tite Trailer Hitch on 2020 Acura RDX
- Q&A: Will the Hands Free Liftgate Feature Still Work on a 2019 Acura RDX with Draw-Tite Trailer Hitch
- Q&A: Pinhole Measurement from Front and Rear of the Draw-Tite # 76268
- Q&A: Which Pin Hole in Draw-Tite 76268 Class III Hitch Is Used for Bike Rack Hitch Pin
- Q&A: What Vehicles Does Draw Tite Hitch part # 76286 Fit
- Article: Trailer Hitch Receiver Sizes
- Article: Hitch Adapters and Extenders
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
on Trailer Hitch
