Which Pin Hole in Draw-Tite 76268 Class III Hitch Is Used for Bike Rack Hitch Pin
Updated 07/04/2020 | Published 07/02/2020
Question:
Hi is it a problem to use the larger pin hole the one closer to the car for a bike rack? The hole is much larger than the pin, but this is the way it seems to work best.
asked by: Sara G
0
Expert Reply:
The Draw-Tite Class III hitch you specified, part # 76268 has two holes in each side of the receiver tube. The larger 5/8 inch diameter hole is meant for the hitch pin. The smaller hole is not used.
So, in regards to your question-the larger hole is indeed meant to be used for the hitch pin.
expert reply by:
Mike L
0
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Article: My Trailer Hitch Doesn't Fit
- Article: Trailer Wiring Diagrams
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Video: Setting up the Draw-Tite Max-Frame Trailer Hitch Receiver on your 2019 Acura RDX
- Video: Curt Mounting Bracket for 4-Pole Flat Trailer Connector Review
- Video: Installation Guide for the Draw-Tite Max-Frame Trailer Hitch Receiver on a 2018 Honda CR-V
- Video: Curt No-Drill Bracket Review
- Video: Feature Review Replacement Hardware Kit for Trailer Hitches
- Video: Set up: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector on a 2020 Acura RDX
- Video: Best 2018 Honda CR-V Trailer Wiring Options
- Shop: Rubber Tube Cover 1-1/4"
- Shop: Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers
- Shop: Draw-Tite Logo Rubber Hitch Cover for 2" Trailer Hitches
- Shop: Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: etrailer Rubber Hitch Cover for 2" Trailer Hitches - Qty 1
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: Pinhole Measurement from Front and Rear of the Draw-Tite # 76268
- Q&A: Removal of Rubber Isolator to Install Draw-Tite Trailer Hitch on 2020 Acura RDX
- Q&A: Recommended Hitch and Wiring Harness for a 2017 Honda CR-V Touring
- Q&A: What Vehicles Does Draw Tite Hitch part # 76286 Fit
- Q&A: Does the Exhaust Have to Be Lowered to Install the Draw-Tite Hitch 76268 on a 2019 Acura RDX
- Q&A: If OEM Cutout Fascia Piece Needed When Installing Draw-Tite Trailer Hitch on a 2019 Acura RDX
- Q&A: Does the Draw-Tite Hitch for a 2019 Acura RDX Stick Out Past the Bumper
- Article: Trailer Hitch Receiver Sizes
- Article: Hitch Adapters and Extenders
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
Explore Expert Info
![Our Expert]()
on Trailer Hitch
on Trailer Hitch
