Is A Weight Distribution System Needed To Pull My 6,000lb Trailer With My 2022 Ford F-350?

Question

Question:

I have a 2022 F350 and a 6k pound 30’ RV. Do I need a WD hitch to pull that less than a 100 miles? I had a F150 with a WD hitch and the sway bars. That truck definitely needed the WD and sway control, but not sure if my new truck does. Thanks for your help.

asked by: Shayne

0

Expert Reply:

Anytime a trailer's fully loaded weight is over 50% of the tow vehicles gross weight it is recommended to use a weight distribution system.

I went ahead and found that your 2022 Ford F-350 has a GVWR range of 10,100lbs - 12,400lbs. If your trailer fully loaded is under 6,200lbs, then you don't technically need a WDS, but it wouldn't hurt to have one.

If you're interested in a WDS, the Reese Pro Round Bar Weight Distribution w Sway Control # RE44FR is a great option that'll work for you, and will create a more balanced and level ride

This system has a gross towing weight capacity of 11,500lbs, a tongue weight capacity range of 600 lbs - 1,150 lbs, and a includes the head with preinstalled ball, a shank, sway control brackets, spring bars, lift-assist bar, and all necessary hardware.

expert reply by: Bryce D

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

Hey Brian! It looks like you decided to go with the MORryde GooseTech #MR27MV, which is a great option. However, the GVWR of your 2023 Keystone Montana 3231CK is 16,680 lbs and this is designed for 18k+. Also, did you verify that your pin box bolt…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hello David, Thanks so much for reaching out! For your 2026 Ford F-350 diesel dually, you will want the EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2" #EH54QR. This is the only front mount option we offer that is confirmed…

view full answer...

Answer 12

Hi Bill! Thanks for your pictures, they were extremely helpful! ^___^ The LCI Part #194170 on that tag you found means you have a 1621 pin box. The Gen-Y #GY45SR you were looking at is specifically for the Lippert 1116 and 1716 pin boxes, so you will…

view full answer...

Is A Weight Distribution System Needed To Pull My 6,000lb Trailer With My 2022 Ford F-350?

Continue Researching