Will Kodiak Disc Brake Kit Fit 2000 Four Winns Horizon 180 Boat Trailer

Question

Question:

Hello, Is it possible to tell me if these will work on a 2000 Four Winns Horizon 180 Boat trailer? It is a single axle trailer with 15inch 6 lug wheels 5.5inch pattern, model #DO18190. Thanks for any help you can provide.

asked by: Steve G

0

Expert Reply:

From what I was able to find, the typical axle used on the boat trailer for your 2000 Four Winns Horizon 180 uses a 5,200 lb axle. I recommend verifying this information by looking at the axle tag on your trailer axle. Based on this and the bolt pattern you have, the Kodiak Disc Brake Kit - 12" Rotor - 6 on 5-1/2 - Dacromet and KodaGuard - 5,200 to 6,000 lbs # K2R526DKG is the correct kit for your trailer.

expert reply by: Robin H

0

Answer 1

Hey Scott, you can use 6-on-5-1/2 idler hub assembly #AKIHUB-655-6-EZ-K to replace what you have based on the part number you found on the hub. Then for Bearing Buddies you'd want the part #BB2441SS.

view full answer...

Answer 2

The Electric Trailer Brake Kit part #AKEBRK-35-SA is likely what you need for your Four Winns Boat Trailer. The 3,700 lb trailer axles usually use the same spindles as 3,500 lb trailer axles so as long as you have 10" assemblies (roughly) and…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Will Kodiak Disc Brake Kit Fit 2000 Four Winns Horizon 180 Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching