What Does Load Range C Mean for Trailer Tires

Question

Question:

What does load range C mean?

asked by: Dorethia G

0

Expert Reply:

Trailer tires are organized by Load Ranges which basically represents the weight capacity for that tire size. So for example the Load Range C trailer tire and wheel part # AM32395 that you referenced has a weight capacity of 1,820 lbs at 50 psi. Different tire sizes would have different capacities at the same Load Range.

expert reply by: Jameson C

0

Answer 1

The Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs #RR5K are rated for 5,000 lbs break strength and will work just fine with your application. The 3/4 inch plywood floor is very strong and with the…

view full answer...

Answer 2

Generators do not typically have a 12 volt power converter, so I recommend using the Battery Charger and Maintainer #CTEK56353 and splicing the connector that would go to the battery terminals into a 7-way connector like #30717. You will connect the…

view full answer...

Answer 3

Yes, the Bulldog Powered Drive Trailer Jack - Black #BD500199 can be wired to either a battery or to the 7-way. If you wire it to the battery you'll be able to operate the jack any time, as long as the battery has a 12v charge. If you wire it to…

view full answer...

Answer 4

You could do the Kenda #AM30660 and safely pull at 65 mph. This is our only option for a pre-mounted tire and wheel combo. I strongly recommend going with a tire with a higher speed rating, but to do this they will not come mounted on the wheel. You…

view full answer...

Answer 5

Differences in Load Ranges mean different weight capacities for the tire. In the tire size of 235/85-16 that you referenced a Load Range F means 3,960-lb maximum load at 110 psi capacity and Load Range G means 4,080-lb max load at 95 psi. Kenda is…

view full answer...

Answer 6

To measure the width of a trailer wheel you will measure from where the tire beads will seat on the wheel. That will be from the inside of the inner wheel flange to the inside of the outer wheel flange, not from edge to edge of the wheel. To measure…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

Speed is a huge issue with trailer tires actually. Unless otherwise noted trailer tires are rated as 65 miles per hour as their max speed. Exceeding the speed rating will cause the tire to heat up and fail easier. We do have a couple brands that have…

view full answer...

Answer 9

It depends on how much clearance you currently have around your wheels. Ideally, you should have 3 inches minimum clearance between your fender and your wheels and an inch minimum between your sidewall and trailer frame/wall. As your wheel size…

view full answer...

Answer 10

For that size tire, 4.80 X 8, I recommend the Kenda tire, #AM10004. This tire has the Load C rating and fits the 8 inch x 3-3/4 inch rim. Using the heavier load range could extend the life of this tire. The Kenda tire is a bias tire that tend to run…

view full answer...

Answer 11

The two tire sizes you referenced, 4.80-12 and 5.30-12, both fit 4-inch wide rims, but they differ in their overall diameter. A 4.80-12 tire/wheel when fully inflated will have a diameter of 20-1/2-inches while the 5.30-12 size will be just under…

view full answer...

Answer 12

The speed rating limitation for a trailer will come down to the tires, it has little to nothing to do with the axle, hub, or wheel size. That said, smaller tires generally do have lower speed ratings but you do not need to upgrade the wheels on your…

view full answer...

What Does Load Range C Mean for Trailer Tires

Product Page this Question was Asked From

Continue Researching