Replacement For Hub & Drum 8-207

Question

Question:

I have a trailer hub that is cracked. Molded into the hub casting is Dexter 8-207. Could you tell me what hub I would buy to replace my hub? Thank You

asked by: Avery

0

Expert Reply:

I can indeed; the correct replacement for your 8-207 Dexter hub and drum is the following:

- Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 # 84546UC3

expert reply by: Kyle S

0

Answer 1

The #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axles #TRU87FR is designed to fit 3,500lb axles that are 2-3/8" outside diameter. The narrower portion of the spindle is roughly 2" to fit inside the axle tube and will angle out…

view full answer...

Answer 2

The #84 E-Z Lube Spindle with Brake Flange for 3,500-lb Trailer Axles - 4" Drop part #TRU87FR is designed for a 3,500 lb axle with a 2-3/8" outer diameter. I don't have a list of every trailer that the spindle will fit but so long as…

view full answer...

Answer 3

The UFP hub that you've referenced isn't made any longer I don't believe, but we do have some options for you. From some previous customers, we've determined that the UFP H-1062-3 axle has a spindle that has #L44649 inner and outer…

view full answer...

Answer 4

It sounds like your trailer has the 6-1/2 inch Oval stop turn and tail lamps and some side marker lamps that use a rubber grommet like the 6-1/2 inch oval tail lights grommet, #A70GB. Since the area where your lights are mounted is not accessible…

view full answer...

Answer 5

To determine your spindle size, you can either pull one hub off your trailer and look at the bearing numbers on the face of the inner and the outer bearing, or you can measure the spindle itself. I've attached an article and a photo to assist. If…

view full answer...

Answer 6

Based on the Dexter 10 inch hubs we carry, all have 1/2 inch diameter pressed in lugs. The screw in options are rare and only on a couple of the 12 inch drum assemblies we carry.

view full answer...

Answer 7

We do actually have Dexter electric drum brakes in your required 10 x 1-1/2-inch size, parts #K23-473-00 and #K23-472-00, which are right- and left-hand, respectively. These are complete bolt-on (4-bolt) replacements that fit wheels diameters from…

view full answer...

Answer 8

Brake flanges on 3,500 lb axles are going to be the exact same between a Dexter axle and Lippert but sometimes the Al Ko options are different. I believe you are asking about the price difference between the Dexter 3,500 lb axles part #T3584F-8974…

view full answer...

Answer 9

Wheel bolt patterns are defined by two numbers: the first being the number of lug nuts and the second being the diameter of the circle the lug nuts are arranged in. So a 5 on 4-1/2 bolt pattern is 5 lugs arranged in a circle that is 4-1/2 inches in…

view full answer...

Answer 10

Those are Warner trailer brakes. This style is not made anymore and replacement parts are hard to find. We have some parts for the larger Warner assemblies but NOT the 12 x 2 inch ones. Most people end up replacing them. You will have to have…

view full answer...

Answer 11

It's not common for hyper-flash to occur on a trailer but this comes down to which trailer wiring harness is installed on the tow vehicle. If you are tied into the vehicles tail light circuits as opposed to a tow package port then hyper-flash is…

view full answer...

Answer 12

I can help you find the right assemblies, but I do not know exactly which ones you have on your 2008 Palomino 25RS. To pick out the correct brake assemblies for your trailer you need to know a few things. You will want to measure the inner diameter…

view full answer...

Replacement For Hub & Drum 8-207

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching