Timbren Silent Ride Suspension Maintenance and Usage Instructions

Question

Question:

Would you have information on the design of pivot points, are these using bushings and are they manufactured with lubrication points. Is there any literature on the maintenance and repair procedures available.

asked by: Randall

0

Expert Reply:

I reached out to my rep at Timbren and got some information for you on the Timbren Silent Ride Suspension for Tandem Axle Trailers w/ 3" Round Axles item # TSR14KT01. The silent ride requires little to no maintenance. You are supposed to check the bolts before & after use periodically, and keep the unit clean as possible. There are no lubrication points on the suspension. The three pivot points allow easy suspension movement, creating a gentle ride. The suspension arm freely articulates around the pivot point ensuring full equalization, so all of your tires make full contact with the ground at all times. These three points also make it easy to lift the tongue of the trailer and move it by hand. They did not have any literature on the maintenance and repair procedures.

expert reply by: Jerred H

0

Answer 1

We do have the correct bearings and seal for your Timbren Heavy-Duty Axle-Less Trailer Suspension - 4" Lift Spindle - Off-Road Tires - 3,500 lbs #ASR35HDS02. What you will need is the following kit, that includes the bearings and grease seal: -…

view full answer...

Answer 2

Thank you for the pictures. Your Timbren 3500 Axle-Less system has the upgraded heavy duty spindle. This will use the Bearing Kit #BK3-100. This will include the following components if you do not want the entire kit. Inner Bearing #25580 Inner Race…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Hey Brandon, I would strongly recommend sticking with the Tekonsha RF brake controller part #TK94FR. We know this works really well and it sounds like it worked well for you too. The Curt Echo is not reliable enough for me to really ever recommend it…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

We can get you everything you need for towing with your 2017 Toyota Sienna XLE. By plastic shield, I believe you are referring to the appearance panel underneath the Sienna, and that will have to trimmed a bit in each of the hitches available for the…

view full answer...

Answer 11

It sounds like you may already have a 4 way connector on your vehicle, which is half of the battle. In order to operate the Curt Echo Mobile Wireless Brake Controller #C51180 you will need an almost fully functional 7 way connector; using something…

view full answer...

Answer 12

Hey Scott! Your 2026 Ford Ranger may or may not have a brake controller port/plug, even with the tow package. There will be four wires coming out of a large wire harness by the driver side firewall, left of the brake pedal, which can be wired to the…

view full answer...

Timbren Silent Ride Suspension Maintenance and Usage Instructions

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching