What are the Mounting Plate Measurements for the Fulton F142425?

Question

Question:

Can I get the width and length of the mounting plate please?

asked by: Eli O

0

Expert Reply:

I had the Fulton XLT 2-Speed Trailer Winch # F142425 measured and have a picture included with the corresponding measurements.

Red: 2-3/4"
Blue: 4-1/8"
Green: 5-3/4"
Pink: 6-7/8"

expert reply by: Lazer S

0

Fulton F142425 Mounting Plate
(click to enlarge)

Answer 1

I attached links to this page that have all of the dimensions for the Fulton F2 Trailer Winch #FW32000101 that you referenced. When looking at it from the front the winch will have an overall width of 14.77", which includes the extension from…

view full answer...

Answer 2

Thank you for providing the picture of your existing mount. This was helpful to idenfication and I have attached it to this post. As you mentioned, the 90 degree snap in holes are 3" apart from center to center. It may be helpful to note that…

view full answer...

Answer 3

Yes, the Fulton XLT Bolt-Thru Swivel Trailer Jack #F141132 that you referenced is designed to fit the same style of mounting bracket that you have in the picture you submitted. This jack will bolt right up.

view full answer...

Answer 4

It sounds like you are looking for the Replacement Hardware Kit for Fulton Swivel Jack, #F0933325S00, along with a 1500 lb jack. For your 1500 lb jack, I recommend the Fulton Bolt-Thru Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,500…

view full answer...

Answer 5

Without knowing the part number and manufacturer of your current trailer jack, I couldn't speak to the compatibility of the mounting plate for your current jack with the mount that the Fulton #F141132 XLT uses. The #P9012-00 weld-on mount for the…

view full answer...

Answer 6

I can't see any part numbers or manufacturer names from your picture, but the Fulton XLT #F141132 does look very similar. I went out to the warehouse and measured the bracket that the bolt, washer, and nut go through for the installation. The…

view full answer...

Answer 7

I went to our warehouse to measure the overall dimensions of the Fulton XLT 2-Speed Trailer Winch #F142418. The main housing measures 6-1/2 W x 10-1/2 L x 7-inches tall. Since the housing has a slightly curved shape these dimensions are approximate.…

view full answer...

Answer 8

The Fulton winches like the part #F142425 that you referenced use an industry standard type bolt pattern that allows the winch to be basically installed on any trailer. This Fulton XLT winches goes even farther with extra, elongated, holes to ensure…

view full answer...

Answer 9

Hey Michael, To make loading your boat easier you'll want to go with a 2-speed winch for a better mechanical advantage if you don't have one already. From there you can go with a higher capacity winch. What is the capacity of your current…

view full answer...

Answer 10

The CE Smith Keel Roller for Boat Trailers #CE29505 is our only self centering keel roller. It is 12" wide versus the 8" that you are looking for. We do have the CE Smith Panel Bracket for 12" Boat Trailer Rollers #CE10305G and Roller…

view full answer...

Answer 11

Hardware is not included with the Fulton XLT 2-Speed Trailer Winch with Heavy Duty 20' Strap #F142418 that you referenced. You'd need to supply nuts and bolts that would work best with your mount plate and the winch.

view full answer...

Answer 12

The weight capacity of your winch really varies depending on what your boat trailer setup is like. If you have rollers then you can use a hand winch that is actually designed to pull less weight because the rollers provide no resistance. For a boat…

view full answer...

What are the Mounting Plate Measurements for the Fulton F142425?

Featured Help Information

Miscellaneous Media

Continue Researching