Valterra Terminal Adapter T1029-4 Maximum Width

Question

Question:

3 inch bayonet X 3 Male threads. My question is what is the outside diameter of this adapter INCLUDing the outside buttonsinch for connections. I need to know to fit in my bumper.

asked by: Judy

0

Expert Reply:

The largest measurement across the diameter of the Valtera # T1029-4 fitting, including the 4 nibs that stick out is 4". I made a graphic showing the measurement below.

I found that my sewer hose would not fit into the standard square bumper on our trailer so I mounted a Valterra # A04-5094BK Sewer Hose Carrier on top of the bumper. You can mount it under your trailer as well. (Also available in white # A04-0150)

expert reply by: Les D

0

Valterra T-1029-4 Hose Fitting
(click to enlarge)

Answer 1

The Stackers Leveling Blocks w/ Bag for Trailers and RVs part #A10-0920 does not come with any wheel chocks. That said, we do offer this separately using the Wheel Chock for Stackers Leveling Blocks part #A10-0922.

view full answer...

Answer 2

The total height of each individual block on the Stackers Leveling Blocks #A10-0916 is 1-3/8 inches. All four blocks included in the set need to be stacked on top of each other to provide the total 4 inches of lift. I have included a helpful…

view full answer...

Answer 3

Yes the Valterra Hose Adapter w/ 3" Swivel Lug Fitting part #F02-2028VP will be a suitable replacement for your needs so long as your pipe coming out is 3" inside diameter. You will remove the old one clean up the end on the old pipe to…

view full answer...

Answer 4

I went out to our warehouse to measure the Valterra Hose Adapter w/ 3" Bayonet and Swivel Lug Fitting #F02-2029VP that you referenced. I found that the lug fitting has an overall diameter, at its widest point, of 4-1/4 inches (which includes the…

view full answer...

Answer 5

Valterra RV Sewer Termination Adapter #T1029-4 has different fittings on each end. One end is a 3-inch lug fitting that mates with a bayonet-style connector like what is on #T1020-1VP and the other is a 3-inch male pipe thread fitting that threads…

view full answer...

Answer 6

Hey John, there's no reason you couldn't use the Blue Ox Wheel Chocks part #BLU47UR on all 4 wheels of your trailer as like a temporary lift. The pair alone has a 30k weight capacity as well so in that regard it would work great too.

view full answer...

Answer 7

Hey Timothy, the EZ Coupler Self Threading RV Sewer hose part #F02-3108 that you referenced basically be used on any RV hose due to it's universal design.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Valterra Terminal Adapter T1029-4 Maximum Width

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching