How does the Bulldog Sidewind Jack # BD150415 Swivel

Question

Question:

Can you tell me if the inner part of the jack swivels? Thanks!

asked by: Tom H

0

Expert Reply:

The Bulldog Sidewind Jack, # BD150415, requires the 2 inch pipe, # BD015279, to swivel. The pipe has 4 holes that are compatible with the 4 holes on the pipe extension on the jack and swivels from the towing position to lifting position with the included pin. I made a short video showing how this jack swivels for you.

expert reply by: John H

0

Answer 1

The foot on the inner tube on Pro Series trailer jack #PS1401480303 is attached, all one part, so you would not be able to add a wheel. None of the pipe-mount swivel jacks come with a wheel. Your best option would be to replace the jack with…

view full answer...

Answer 2

From the top of the tube where the Bulldog Sidewind Jack #BD150415 installs to the top of the jack measures 5-1/2". If you measure from the middle of the pipe then that measurement changes to 6-3/4". I have attached a photo to demonstrate…

view full answer...

Answer 3

You can replace your trailer's jack foot plate with a trailer caster wheel. Your tongue weight capacity will be the lowest of three numbers, 1.) the new caster wheel capacity, 2.) the old tongue jack capacity, or 3.)the trailers stated TONGUE…

view full answer...

Answer 4

The only 8" caster wheel we have is for a Fulton F2 jack with the Wide-Track Wheel Assembly #F500266. This does have a cross-pattern style attachment though so if you have something other than a Fulton F2 it won't work and you'll need to…

view full answer...

Answer 5

Hey Martin, The Replacement Male Pipe for Curt Pipe Mount Swivel Jacks #C46FV has a 2" outer diameter which is pretty standard for pipe-mounted swivel jacks so it would likely be a fit. I wasn't able to confirm the female side of this on the…

view full answer...

Answer 6

Because the fit to the trailer of a pipe mount jack is a little loose due to the large tolerance between the jack and the pipe mount on the trailer, it's pretty rare to find a pipe mount jack with a removable foot that would allow a caster wheel…

view full answer...

Answer 7

On the Ram Removable, 6" Poly Caster, #JC-101, the bolt thread measure 1/2 inch x 20.

view full answer...

Answer 8

Thanks for the pictures. Everything definitely looks the same and the Bulldog #BD150415 is designed specifically for Genie basket lifts. Also, your picture that shows the label code of F3351 helps a lot becasue part #BD150415 has the same label on…

view full answer...

Answer 9

Hey Alan, so the Ram Jack part #TJA-5000S-B that you referenced does have a wheel caster available for it with the part #JC-101.

view full answer...

Answer 10

Hello Jeffery, thanks for reaching out. Take a look at the Ram Removable, 6" Poly Caster Assembly #JC-101. This is a 2" wide 6" diameter wheel. It attaches using a pin, and it will fit a 2" diameter inner jack tube so please do…

view full answer...

Answer 11

The Bulldog Sidewind Jack for Genie Basket Lifts #BD150415 is, as the name suggests, designed to be used with Genie Basket lifts so I assume this is what your lift is. There isn't another jack available that is designed to be used with Genie…

view full answer...

Answer 12

Fulton's Snap-Ring Swivel Jack #FTJ120W0301 fits on a snap ring mount with a pilot hole diameter of 2.313-inches. If this matches you're good to go. If not you might consider just installing a castor wheel on your existing jack. If you…

view full answer...

How does the Bulldog Sidewind Jack # BD150415 Swivel

Continue Researching