What Is Global Link Vise Lock 295-000024 Made Out Of?

Question

Question:

The description says steel construction, but one of the videos say aluminum. So which is it? Also, why is the black latch locks twice the price as the white?

asked by: Scott P

0

Expert Reply:

I reached out to my contact at Global Link and the Global Link Vise Lock for Cam-Action Door Latch - Keyed Alike Option - Black # 295-000024 you were looking at is made out of aluminum, not steel.

The reason the black version # 295-000024 is more expensive than the white # 295-000026 or silver # 295-000025 is due to the popularity of the black version. Since significantly less people or purchasing the other two colors, that makes their price go down.

I included a video of the # 295-000024 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The Atwood AMPlock Trailer Coupler Latch Lock referenced in your question is really designed for trailer couplers to help deter theft of the trailer itself. It secures the trigger latch on the coupler so it cannot be removed from the tow vehicle or…

view full answer...

Answer 2

Hey Jeff, To get a replacement screw hole cover for your Global Link Vise Lock for Cam-Action Door Latch #295-000025 you would need to reach out to Global Link directly. You could also probably find a compatible replacement at your local hardware…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 10

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

What Is Global Link Vise Lock 295-000024 Made Out Of?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching