Bike/Kayak Rack System For Ultra Groove Tonneau Cover

Question

Question:

I already have a Pace Edwards Ultra Groove on my 2020 Silverado 2500 HD. Id now like to add a Bike/Kayak rack. Any suggestions on what I can use.

asked by: Bill G

0

Expert Reply:

Since you already have the awesome Ultra Groove Tonneau Cover on your 2020 Silverado, I would suggest getting the ladder rack # 311-ELF0301 made for your cover # 311-KMFA19A45. This way you can have the kayaks sit over your cab so you don't have to have them hang off the back. If you did have them hanging off the back you would need to insert a load extender # Y01149 on the back. This rack will sit 24.5 inches above your bed rails and the crossbars will be great for using a kayak carrier # e98878 and a bike rack # RKY1222. These racks will accommodate for all the bike and kayaks you throw at it.

This set up will not add any length to your Silverado. I like this just because there is no need to insert anything into your hitch and you won't have to worry about the extra length of your truck so you can maneuver the truck the same with or without a kayak/bike installed.

expert reply by: Adam E

0

click to enlarge

Answer 1

I reached out to my contact at Pace Edwards about the Pace Edwards UltraGroove #311-KMC95A17 you mentioned and he said that it sounds like you don't have enough side-to-side space. Double check the dimensions that are in the installation…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Hey Travis! The right MORryde GooseTech depends on the pin box bolt pattern and GVWR of the Solitude 310GK. If it is a little older it probably has a Lippert 1621, I believe the newer models use the Lippert Rhino. You can ask whoever you're…

view full answer...

Answer 7

I do have an option for you but the Adarac Custom Truck Bed Ladder Rack part #A70490 will not fit with the Pace Edwards UltraGroove Hard Tonneau Cover part #311-KRFA05A28 on the 2019 Ford F-150 with a 5-1/2 ft bed (without cargo management rails)…

view full answer...

Answer 8

For your 2019 Ford F-150 with a 6-1/2 foot bed you do have only two options for a Pace Edwards Switchblade Tonneau Cover. You have the part #311-SWFA06A29 which is aluminum and vinyl and the #311-SMFA06A29 which is aluminum. The aluminum only version…

view full answer...

Answer 9

This problem is due to the rails of your Pace Edwards tonneau not being tapered properly with the shims that came with it. Use the amount of shims that allows it to slightly catch when you go to open it almost to point you have to give it a little…

view full answer...

Bike/Kayak Rack System For Ultra Groove Tonneau Cover

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching