Installing Brake Controller on Farm Tractor For Moving Trailer Around
Updated 12/05/2020 | Published 12/03/2020
Products Featured in This Question
Question:
I want to add a 7-pin RV receptacle on my new 2020 Kioti CK2610 tractor to match the Pollack on my 2003 Dodge Ram 2500 so I can move my goose neck trailer without an adapter. I will need the brake controller as well. What do you recommend? Thank you so much.
asked by: Dave T
Helpful Expert Reply:
I'd be happy to help you with that. Since it's a tractor, there's likely a few differences from what would be seen on a standard passenger vehicle. You very likely won't need to contend with turn signals and taillilghts, and you won't be traveling at highway speeds or speeds typically seen on-road, so the installation will be somewhat simplified.
For a brake controller, a simple and inexpensive time delayed controller like the Tekonsha Power Trac, part # 39523 would work well. The controller is inexpensive, small, and because it's time delayed it can be mounted anywhere within the operator's reach at any angle. It won't need necessarily need to be mounted at any particular angle or in a specific orientation. You'll also need a # 7894 pigtail.
You'll also need a # 38630 circuit breaker and a length of # 10-2-1 duplex cable. You'll need enough wire for one run from the controller to where you'll mount the trailer connector, and for 2 runs from the controller to the tractor battery. You'll also need a # 37185 adapter.
Here's a quick breakdown of the connections. The controller will need a connection to the positive and negative battery terminal (black wire to battery positive, white to battery negative), and will need a wire ran back to the blue wire on the trailer connector to carry the brake controller output voltage. The power feed to the battery would have the # 38630 breaker installed inline.
The tricky part will be the red stop lamp switch wire on the brake controller. If your tractor doesn't have brake lamps, we'll need to do a little wrangling to make that happen, as this is the connection that triggers the brake controller. The easiest solution would be to use a Universal Stop Light Switch Kit, like part # RM-751000. The switch will need 3 connections. One for a constant 12V power source, one to ground and one would attach to the red wire on the controller. This is kinda of a pricey item, but it'll avoid a few headaches because it'll work without needing to fabricate brackets for a regular switch.
The # 37185 would provide the 7-way connector at the rear of the tractor. The only 2 connections you'll really need here is the blue and the white wire. The white wire would ground to the tractor, the blue wire would connect to the output wire ran rearward from the brake controller. The rest of the wires can be tucked out of the way.
Product Page this Question was Asked From
Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Pole Flat Connectors
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Vehicle End Connector
- No Converter
- Factory Tow Package
- 4 Flat
- 7 Blade
- Plug and Lead
- Plug-In
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Brake Controller
- Shop: Vehicle Tow Bar Brake System
- Shop: Roadmaster Universal Stop Light Switch Kit
- Video: In-Depth Review of the Roadmaster Universal Stop Light Switch Kit
- Shop: Trailer Wiring
- Shop: Adapter 4-Pole to 7-Pole and 4-Pole
- Shop: 30 amp. In-Line Circuit Breaker - Perpendicular Mount Bracket
- Q&A: Diagram of the BulletProof Hitches 2-Ball Mount ED304
- Q&A: Adapter for Kubota M7060 Tractor With 7-Pole Round to Connect to 7-Way Blade on Dump Trailer
- Video: Review of Redarc Trailer Brake Controller - Tow Pro Elite Proportional With Wiring Harness - RED42CR
- Shop: Pollak Trailer Connector Adapter - Vehicle End - 7-Pole Round to 7-Way Blade
- Video: Deka Jacketed 2 Wire, 10 Gauge, Brake Wire Feature Review
- Video: In-Depth Review of the Mounting Bracket and Installation Hardware
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - Up to 2 Axles - Proportional
- Shop: BulletProof Hitches 2-Ball Mount for 3" Hitch - 5-1/4" Drop, 4-1/4" Rise - 36,000 lbs
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Custom Harness - Dash Knob - Up to 2 Axles - Proportional
- Search Results: inline fuse
- Search Results: cable cover
- Video: Ultimate Overview of the Curt True Course Advanced Bluetooth Trailer Sway Control
- Search Results: corner latch
- Search Results: latch
- Search Results: 39523
- Search Results: 37185
- Search Results: rm751000
- Video: Complete Breakdown of the Roadmaster Universal Stop Light Switch Kit
- Q&A: Does Curt Hitch Bar part # C55NR Have Weight Capacity
- Q&A: What are the Internal Dimensions of the Curt Solid Steel 3" Hitch Bar with Raw Finish C55NR?
- Q&A: Can the Trailer Valet XL Be Used on Gravel Inclines
- Q&A: Towing a Trailer with Electric Brakes with a Semi Tractor with Air Brakes
- Shop: Towing Mirrors
on Custom Fit Vehicle Wiring
