Can You Haul two 12-Foot Fishing Kayaks on the Malone # MAL25FR LowBed MicroSport Trailer?

Question

Question:

Will the Malone XtraLIght Lowmax Trailer hold a Bonafide SS127 and Perception Pescador Pilot.

asked by: Ina

1

Helpful Expert Reply:

You won't have any problem setting out for adventure with your fishing kayaks on the Malone # MAL25FR LowBed MicroSport Trailer! Your two kayaks weigh 179 pounds total and the LowBed MicroSport has a 800 pound capacity so you can pack on even more. Each of your kayaks are 33.75" which will both fit easily on the 78" wide crossbars. Also, the LowBed MicroSport supports boats up to 20' and since yours are less than 13', this too will be no problem. You will be able to tie down your kayaks to the crossbars.

I really like the LowBed MicroSport's fully galvanized frame, the modern LED lights and that it is made in the USA.

Since you have some weight capacity to spare you should definitely think about the Malone # MPG481 Storage Trunk that fits perfectly in between the frame in the pack. This is the perfect place to store tie down straps, wheel chocks, and fishing gear while you are in transit. There are some flanges that let you use a lock as well. I have included a link below.

expert reply by: Les D

1

Answer 1

The Malone LowBed MicroSport Trailer #MAL25FR and Malone MicroSport Trailer #MPG461B2 are very similar as they are both built on the same platform. This allows them to both carry the same weight and size kayaks. The #MPG461B2 has a 30" height to…

view full answer...

Answer 2

Hey Tanya, thanks for reaching out! To tow your trailer you'll need a ball mount with a 2" rise and for that I recommend going with the etrailer Ball Mount Kit #e38NR. This gives you a 2-3/4" rise but that will still work for your…

view full answer...

Answer 3

The crossbars of the Malone #MAL25FR LowBed MicroSport trailer are 78 inches in length. From what I found online, the Hobie Mirage Outback kayaks are about 34 inches wide which would provide plenty of room as the bunks are width adjustable and can be…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Barry, yes the lowbed coversion kit part #MAL33TR and the retractable tongue kit part #MPG494 are both a fit for the Malone Microsport Trailer part #MPG460G. What are you planning on using the Microsport for?

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Can You Haul two 12-Foot Fishing Kayaks on the Malone # MAL25FR LowBed MicroSport Trailer?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching