How Does Breakaway Lever of Titan Model 60 Actuator Reset

Question

Question:

I forgot to unhook and pulled the actuator forward can’t get it to release back ?

asked by: BJ

0

Expert Reply:

I've spoken with Titan about resetting their model 60 actuator breakaway levers in the past and they have told me that you have to remove the cover and then carefully remove the spring inside. Then set the lever in the disengaged position and re-insert the spring.

expert reply by: Jameson C

0

Answer 1

I spoke to my contact at Titan about resetting a Titan Model 60 actuator which is not the Dexter part #099-175-20. You have to remove the cover and then carefully remove the spring inside. Then set the lever in the disengaged position and re-insert…

view full answer...

Answer 2

To bleed the brake lines on a Titan Zinc-Plated Brake Actuator #T43397007K I recommend using the Powerbuilt Brake Bleeder #ALL648591. This has a magnet that will hold the catch container where it is easily visible. Using the 4 steps detailed in the…

view full answer...

Answer 3

The Titan Zinc-Plated Brake Actuator part #T43397007K is a complete fully functional unit so yes, it does come with the master cylinder.

view full answer...

Answer 4

Hey Dave, To retract the breakaway cable, slide the coupler fully forward and push up on the pushrod release bracket located on the underside and behind the hitch ball socket to allow the bead to retract into the actuator. This will release the…

view full answer...

Answer 5

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Not another one! Just kidding Dirk! I was in the Marines I enjoy these conversion questions on the M1101 trailers. I'd be more than happy to list the parts you need, along with quantity, and confirm compatibility. 1 - Timbren Axle-Less Trailer…

view full answer...

Answer 8

I would be happy to help you. The Brake Actuator with Manual Lockout - Bolt On - Drum - 2" Ball - 7,500 lbs item #T4500600 you referenced is recommend to be mounted on a 3" wide tongue. It is an industry standard actuator and has an inside…

view full answer...

Answer 9

For a Four Winns Boat Trailer with Titan Aero 6000 Surge Brake Actuator, I recommend replacement using the Titan Zinc-Plated, Leverlock Brake Actuator part #099-175-20 which is ready to go as is and will be a great fit. The reason I recommend…

view full answer...

Answer 10

It does not come with instructions but it is pretty easy to replace. For your Titan Aero 6000 the correct replacement master cylinder is item #T4395100. This is the replacement master cylinder that works with drum brakes. I was able to find an…

view full answer...

Answer 11

There sure is! You'll be needing the Lockout Key #DX94FR for your Brake Actuator #T4606520. Do you use the key much? Or are you using the electric solenoid?

view full answer...

Answer 12

That's a really good question, and there is a difference between the 7,500 lb Dexter DX7.5L A-60 actuators for disc brakes; the differences are both in what they fit, as well as their length. - 14" Long & Top-Mounted For 3" Wide…

view full answer...

How Does Breakaway Lever of Titan Model 60 Actuator Reset

Product Page this Question was Asked From

Continue Researching