Replacement Hatch Strut for Stabilus STX29-100 on 2012 Crownline 285 SS Bow Rider Boat

Question

Question:

Will this product replace the gas shock on the back hatch of a 2012 Crownline 285 SS Original Part: Stabilus STX29-100?

asked by: Nick M

0

Expert Reply:

From what I've been able to determine, the existing struts you have are 36 inches long and provide 100 lbs of compression force and have a 3/8 inch ball socket on each end. The # 3691871-80 are also 36 inches long when fully extended but have a 80 lb compression force, so you'd want to use # 3691871-100 which has a matching 100 lbs of compression force. This strut is compatible with a 13mm ball socket which is larger than what your original struts used so you'd need to replace the ball studs with 13 mm ones like # 3691890. Y

expert reply by: Mike L

0

Answer 1

The right and left orientation is determined if you are standing behind the trailer looking towards the tow vehicle. The left side is the drivers side and the right side is the passengers side. Tthe shorter brake pad will always be in the front of…

view full answer...

Answer 2

Typically around the motor area of the stabilizer jack there will be a label that will have part numbers and other info listed. I attached a picture of what it looks like on the #LC298707 that you referenced. Lippert does sometimes use alternate part…

view full answer...

Answer 3

We do carry the Replacement Hydraulic Jack Assembly #LC43ED for your Thor 34R class A motorhome. This is the Lippert part number 372892 they gave you.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

Hey Kris, the Dutton Lainson winch part #DL15440 does not come with a strap so you will need to order one with it. The part #DL24250 will work great with this winch as it is correct width, is 25 feet in length, and has a capacity of 3,700 lb WLL and…

view full answer...

Answer 12

Hello James, thanks for reaching out. Both the kits you mentioned, the Hydrastar #HYD22FR and #HYD42FR are complete conversion kits for standard 3,500 lb axles. The difference is the calipers included with each kit. The #HYD22FR has stainless steel…

view full answer...

Replacement Hatch Strut for Stabilus STX29-100 on 2012 Crownline 285 SS Bow Rider Boat

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching