Correct Replacement for Atwood G6A-7E Water Heater

Question

Question:

Is Atwood water heater#G6A-8E and replacement for G6A-7E?

asked by: Ronald M

0

Expert Reply:

The correct replacement for an Atwood G6A-7E Water Heater is the Atwood RV Water Heater w/ Heat Exchange part # AT96136 (GH6-8E). This new unit has the same gas only operation, 6 gallon capacity, and automatic pilot light as the model you have now so it's an exact replacement.

expert reply by: Conner L

0

Answer 1

The only tank equipped RV water heat option we currently offer is the Dometic RV Water Heater part #DMC74FR which is a 120 volt unit with 6 gallon tank and gas/electric operation. In regards to installation, this must be performed by a qualified…

view full answer...

Answer 2

After looking into this, everything I can find says that this unit falls under the Mach 3 category. The MaxxAir TuffMaxx Replacement RV Air Conditioner Cover for Coleman-Mach RV Air Conditioners #MA00-325001 is designed to fit Mach-1, Mach-3 and…

view full answer...

Answer 3

I reached out to my contact at Dometic Atwood and she said that the correct water heater to replace your existing model GC6A-7E is the Atwood #AT96117. This will be a perfect replacement that features a 6 gallon tank and an 8,800 Btu heating…

view full answer...

Answer 4

The dimensions I could find for a Norcold 1210 fridge are 68.88 T x 37.88 W x 28.75 D. The closest 12v fridge we carry to this size would be the Everchill RV Refrigerator w/ Freezer Drawer #WAY44FR, which is 28-1/2" wide x 72" tall (at…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Correct Replacement for Atwood G6A-7E Water Heater

Continue Researching