Air Lift Air Suspension WirelessAIR Compressor Assembly Showing BLOC Error Code

Question

Question:

The compressor runs and shuts down with era code “ bloc”. Lines to springs are clear. Air from compressor with good volume and pressure. Air out or manifold next to zero. What do I do?

asked by: Mark R

0

Expert Reply:

The 'Bloc' error code you're reading on your AirLift # AL72000 compressor system does indeed mean that there's a blockage in the system, according to Air Lift the overwhelming majority of the time given what you've troubleshot up to this point the problem is in the water trap canister joined to the manifold. There's a spring in there can can get dislodged and once that occurs, the compressor will just dump all the air out of the water drain. Simply disassemble the water trap assembly by unscrewing the cylinder and clean the spring and plunger. Give the parts a good shot of a spray lubricant like WD-40 and reassemble. That should solve your problem.

I've provided a photo showing where the water trap assembly is located.

expert reply by: Mike L

0

click to enlarge

Corey C.

4/7/2024

I did what you said and it will only pump till 20 lb then say block I hit the arrow to pump more it pumps but numbers stay at 20 then stops saying block

Mike L.

4/10/2024

@CoreyC The 'Bloc' error code you're getting on your AirLift compressor system indicates that there's a blockage in the system. Most often, the problem is in the water trap canister joined to the manifold. There's a spring in there can can get out of place and when that happens, the compressor will just dump all the air before it can reach your desired pressure. You'll need to take apart the water trap assembly by unscrewing the cylinder and clean the spring and plunger. Give the parts a good soaking of spray lubricant like WD-40 and put it back together which should fix the issue.

Paul Z.

5/15/2025

@MikeL Do you need to use a pipe wrench to separate the filter mine is definitely tighter than my hands can move it.

Mike L.

5/29/2025

@PaulZ I'd try some channel locks. My fear is that a pipe wrench would destroy the housing...

Answer 1

It sounds like your bags aren't installed properly if one of them is angled. There are two alignment holes that the bag can install into on the top mounting bracket. It is possible that the wrong one was used for your bags and that is why the bag…

view full answer...

Answer 2

The error code #9 under current is saying your Air Lift WirelessAIR Compressor System #AL74000 is not getting the power it needs from the battery to run. First you will want to check battery and ground connections to ensure they are not loose or…

view full answer...

Answer 3

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 4

Generally this is an issue with the remote #AL73002 communicating with the system #AL74000, a blockage, or a leak. I would inspect the compressor system and all of the air lines to make sure there are no issues. You can check for leaks using soap and…

view full answer...

Answer 5

I reached out to AirLift to see what could be going wrong with your Air Lift WirelessAIR Compressor System part #AL74000. They informed me that the A-09 code is a low voltage code. With this issue you want to check all of the connections on the…

view full answer...

Answer 6

Replacement Manifold for Air Lift WirelessAIR Compressor System for Air Helper Springs AL26558 is a replacement for the WirelessAIR model compressor systems. Your WirelessONE Gen 1 system is no longer manufactured so the only way to find a…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Air Lift Air Suspension WirelessAIR Compressor Assembly Showing BLOC Error Code

Featured Help Information

Miscellaneous Media

Continue Researching