Is the MCL40RB a 2 Diode LED Light?

Question

Question:

Can you confirm if the light shown in the attached pics is the same as MCL40RB. I cant see the inside of your light so dont know if it is the same. I do have a 2 diode light which measures 4 x 1 1/2. Thanks.

asked by: Matt E

1

Helpful Expert Reply:

The LED Clearance of Side Marker Light # MCL40RB is the same light as the one you've got pictured. This light is also a 4" x 1-1/2" light with 2 diodes and will be an acceptable replacement for the light shown in your picture. The mounting holes on the # MCL40RB are 3" apart, center on center.

expert reply by: Erik B

1

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

Hey James, that light looks like the #MCL40RB which means for a replacement lens you'd need the part #A44RB.

view full answer...

Answer 7

Hey Trey. Not sure what product your question is directed at. The Optronics Utility Work Light item #TL35TB you were looking at measures 6-5/8" long x 4-5/16" wide x 3-13/16" deep. It comes with a mounting bracket that screws into the…

view full answer...

Answer 8

The correct replacements we offer for the Glo Brite Marker Lights 118A and 117R is the Trailer Clearance or Side Marker Light part #MC44AB for amber and part #MC44RB for red.

view full answer...

Answer 9

Hey Brian, we do not have a thermostat control setup for your roof vent. If that's something you needed you'd have to go with a different vent assembly like the MaxxFan part #MA00-04002K.

view full answer...

Answer 10

Hey Holly, we have bulb seals like it sounds like you are looking for but the widest option we have is 3-3/16 inches like the part #SR68FR which is 60 foot long.

view full answer...

Answer 11

For your van, I recommend the Advent Air RV Air Conditioner w/Vent, Start Capacitor, and Heat Strip Black #ACM135BCH. This unit will cool or heat your space in about 2 minutes and will give you a temperature range of 60-85 degrees. There are 3 speeds…

view full answer...

Answer 12

It appears you are going to need to change out your spindle for the BTR Spindle #TRU44FR. This will allow you to use either a 4 on 4" Hub #AKIHUB-440-2-EZ-2K or 5 on 4-1/2" Hub #AKIHUB-545-2-EZ-2K depending on your wheel bolt size. I cannot…

view full answer...

Is the MCL40RB a 2 Diode LED Light?

Product Page this Question was Asked From

Continue Researching