Which replacement spring for a 2005 Bigfoot 21RB travel trailer
Published 08/29/2019
Question:
I got underneath the trailer, but did not jack it up and put it on jack stands so this is a all wheels down, laden weight measurement as close as I can estimate, since the spring eyes’ holes are filled. I measured 24.5” middle of spring eye to middle of spring eye. I also measured the diameter of the axle by measuring the distance across the U Bolts at 2.5”. Hope this helps. Thanks again.
asked by: Bill W
Helpful Expert Reply:
I looked up your 2005 Bigfoot 21RB and found that it is a tandem axle trailer. I couldn't find the GVWR for your specific model though. Most seemed considerably lighter than what you mentioned so you might verify what you have. Or you can get me the diameter of your axles and that would be a good indicator.
The axle info should be listed on a sticker that's on the axle as well. Or it can be listed on the VIN plate/sticker of the trailer.
Product Page this Question was Asked From
4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/4" Long
- Trailer Leaf Springs
- Double Eye Springs
- 9/16 Inch Eye
- Nylon Bushings
- 3500 lbs
- 1-3/4 Inch Wide
- 4 Leaf
- 25-1/4 Inch Long
- Standard Grade
- etrailer
more information >
Continue Researching
- Shop: Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs - 3-1/8" Links
- Shop: Dexter Heavy Duty Suspension Upgrade Kit for Single Axle Trailers -3-1/8" Shackle Straps
- Shop: Hydraulic Trailer Jack w/ Counter Balance Valve - Left - 24-1/4" Lift - 12,000 lbs - Bolt-On
- Shop: Bigfoot Hydraulic Jack Set - Dual Pump - 24" Lift - 24,000 lbs
- Q&A: Troubleshooting Slanted Equalizer on Unloaded 7K Cargo Trailer
- Q&A: Hanger Spacing Needed for 25-1/4" Leaf Spring on Single Axle Trailer
- Shop: 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/4" Long
- Shop: Dexter Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 38" Axle Spacing
- Search Results: pressure relief valve
- Video: Feature Breakdown: Folding Shelf Bracket
- Search Results: hitch bike racks
- Q&A: Pressure Relief Valve For A Furrion FWH09A-AM Water Heater
- Search Results: stl72rb
- Q&A: Hanger Spacing for 3500 LB. Tandem Axle Trailer
- Q&A: Can the Valterra Heating and A/C Vent Register Rotate to Control Direction of Air
- Q&A: Recommended Cleaning Agents For A Furrion Tankless RV Water
- Shop: Bearing Buddy Bearing Protectors - Model 1980 - Chrome Plated (Pair)
- Search Results: k23~429~00
- Search Results: 12114
- Search Results: bearing buddy 1980
- Search Results: a70gb
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Video: How to Choose a Trailer Brake Controller
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
on Trailer Leaf Springs
Bill W.
8/29/2019
I got underneath the trailer, but did not jack it up and put it on jack stands so this is a all wheels down, laden weight measurement as close as I can estimate, since the spring eyes’ holes are filled. I measured 24.5” middle of spring eye to middle of spring eye. I also measured the diameter of the axle by measuring the distance across the U Bolts at 2.5”. Hope this helps. Thanks again.