Does Prodigy P3 and P2 Brake Controller Use Same Install Harness

Question

Question:

Is the harness 3015-P for the P3 the same harness as the one used for the P2. I have a P2 on my 07 chevy 2500hd classic and would like to upgrade to a P3 but dont want to buy a new harness if its not needed. thanks

asked by: William K

0

Expert Reply:

The install harness of a Prodigy P3 part # 90195 and the P2 part # 90885 is the exact same so all you'd have to do is unplug the harness from the back of the P2 and then plug that into the back of the P3 and you'd be set.

expert reply by: Jameson C

0

Answer 1

For the pads between the hitch and rails of your 5th wheel setup, I recommend the Curt Fifth Wheel Rail Sound Dampeners #16900. These pads are designed to eliminate common rattle when driving.

view full answer...

Answer 2

Thanks for the well wishes! There are two primary differences between the original Tekonsha Prodigy and the newer Prodigy P2. The P2 will actuate electric over hydraulic trailer brakes, where the original Prodigy will not. The original Prodigy needed…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 9

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

Answer 10

Hey Dave! For a replacement 60A converter that is lithium compatible to replace your 9260C I recommend the Progressive Dynamics 9300 Series RV Converter Charger #PD79RR. Progressive Dynamics makes great products, and this includes all the same safety…

view full answer...

Answer 11

I sure do Ronnie and welcome back! The Dexter Nev-R-Adjust Electric Trailer Brakes item #23-458-459 are exactly what you need. These self adjusting set of brake assemblies will replace the 12" ones currently on your Airstream trailer. They have…

view full answer...

Answer 12

Hi Robert; you could use the LaSalle Bristol Waste Valve #34466N11AA as a replacement but the handle will sit underneath the trailer right at the valve. Looking at the Grand Design parts site it looks like you have a 1-1/2" Valterra with a…

view full answer...

Does Prodigy P3 and P2 Brake Controller Use Same Install Harness

Continue Researching