Could Yakima Overhaul Ladder Rack Fit with Truck Bed Tool Box

Question

Question:

Can this be used in a short bed truck that also has a truck tool box in it?

asked by: Jimmy H

0

Expert Reply:

If the tool box was a chest style that didn't go over the tops of the bed rails the Yakima Overhaul HD Adjustable Truck Bed Rack # Y01151 would easily install without issue. Due to how this wraps around the bed rails (see picture) it couldn't fit with a crossover style box.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The underside base plate pad of the Yakima Overhaul #Y01151-5855 is 20 inches long, by 6 inches wide, and 3/4 inch thick.

view full answer...

Answer 2

Yes. The TS (T-Slot) Rails for Truck Hero Elevate Rack System are compatible with the Truxedo LoPro and the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack for Tonneau Cover part #Y01151-5755.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Brett, the best option we have would be the Yakima Overhaul HD part #Y01151-5768 which is an adjustable height ladder rack that attaches to the utility track you have above the storage containers in the bed of your 2022 Toyota Tacoma Trail…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Lucas, It looks like both the Redarc #RED72CR and #RED68CR are going to include the same wire harness #RED99FR, but the #RED72CR is also going to include some mounting panels to make mounting the control knob into your dash easier so I'd go…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

Hey Richard, congrats on the new truck! It is a bummer that your old TracRac cannot be used on your new truck, but we do have some other good options for you. If you liked your TracRac, we have the Thule TracRac TracONE #TH27000XT which will fit the…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Lon, yes the Air Lift LoadLifter part #AL49DQ would be a great option for your 2023 Toyota Tacoma TRD. IT will give you the support you are wanting but since you can easily adjust air pressure you'd also be able to easily tailor the…

view full answer...

Answer 11

Hey Kye, thanks for reaching out! Not all lift kits are made equal, so in order to determine what (or if) you need spacers with the Air Lift LoadLifter 5000 Air Helper Springs #AL49DQ you'll need to either reach out to the company that made the…

view full answer...

Answer 12

Yes! For mounting the Malone TradeSport Ladder Rack #MAL55VR to your Toyota Tacoma, you need to use the included Toyota Tacoma fit kit hardware. This kit is designed specifically for your truck. I went ahead and attached a screenshot of this fit kit…

view full answer...

Could Yakima Overhaul Ladder Rack Fit with Truck Bed Tool Box

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching