Parts Needed to Use the Yakima HoldUp 2 Bike Rack for 2" Hitches with a 1-1/4" Hitch

Question

Question:

Is there a tongue that will convert a 2inch Yakima Holdup to a 1.25? This product just looks like its a 2, which I already have. Would need a 1.25inch tongue replacement.

asked by: COREY

0

Expert Reply:

To convert your Yakima HoldUp 2 Bike Rack for 2" Hitches # Y02443 so that it will fit a 1-1/4" hitch receiver you need the Replacement Tongue # 8880581 along with the Hardware Kit # Y90195. Please note that when using this smaller tongue you cannot utilize the 2-Bike Add-On # Y02446. You will only be able to carry 2 bikes with the 1-1/4" tongue.

expert reply by: Jon G

0

Answer 1

The correct replacement anti rattle hitch pin for your Yakima HoldUp Bike Rack #Y02445 is the Replacement Mounting Hardware for Yakima HoldUp #Y8880129. Unfortunately this, like most other bike rack anti rattle hitch pins is a proprietary pin and…

view full answer...

Answer 2

To replace the threaded hitch pin and lock for your Yakima HoldUp, it will depend on if you have the 2" shank or if you have the 1-1/4" shank with a 2" adapter. For the 2" shank, you will need the Replacement Hitch Bolt and Clip…

view full answer...

Answer 3

Yes, the bolt will tighten all the way up to being flush with the hitch opening. Check out the pictures I attached that show what it will look like once installed. You might try removing the rack from your hitch and seeing if it will thread all the…

view full answer...

Answer 4

Yakima has a few different anti-rattle threaded hitch bolt designs and the one you want for your Yakima EXO SwingBase Swing Away Hitch Extender #Y34VR is part #Y52FR on our site. This is the same as the 8880953 you mentioned, it just has our part…

view full answer...

Answer 5

I checked with Yakima and the correct replacement hitch pin you need for your BackRoad is the part #Y8890176.

view full answer...

Answer 6

Yes, the Holdup for 1-1/4 inch hitches requires a different, smaller hitch pin. For that you'd need the part #Y90195 which comes with the new wrench you'd need and the smaller hitch pin for use with the #8880580.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

The Hollywood Racks Trail Rider 2-Bike Rack #HR200 weighs about 35 lbs. The Swagman XC 2-Bike Rack #S64650 is lighter at about 26 lbs. The biggest difference between the two is the Swagman rack is rated for 2 bikes at 35 lbs each and the Hollywood…

view full answer...

Answer 12

The Swagman XTC4 4-Bike Rack #S64665 and Hollywood Racks Destination 4-Bike Rack #HR4000 are two of the best values in regards to 4-bike racks, and when taking everything into consideration I highly recommend the Destination #HR4000. There are a…

view full answer...

Parts Needed to Use the Yakima HoldUp 2 Bike Rack for 2" Hitches with a 1-1/4" Hitch

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching