Dimensions of the Opening on Replacement Manual Override Crank # BD500203

Question

Question:

Will this work on a forest river travel trailer ? my main concern is the diameter of the socket .

asked by: Richard C

0

Expert Reply:

I went out to the warehouse and measured the end of the manual override crank # BD500203 that attaches to the jack so that you can compare it with the manual crank location on your jack.

The diameter of the socket is 7/8", it is about 1/2" deep, and the slit on the sides is 1/4" wide.

expert reply by: Jameson C

0

click to enlarge

Answer 1

From the picture that you sent, it does look like the Replacement Manual Override Crank #BD500203 is a possible fit. The reason I say possible is because I am not sure what the dimensions are in the picture that you supplied. I went out to the…

view full answer...

Answer 2

You can use the Replacement Manual Crank Handle for Stromberg Carlson Electric Trailer Jacks #SC94VR as a replacement crank for your Stromberg Carlson Electric Trailer Jack #JET-5000.

view full answer...

Answer 3

We have found that for your Atwood model 71119 jack the correct replacement motor is the Lippert #LC141893. This particular motor is used for many applications including tongue jacks like what you have and 5th wheel landing gear systems. If your…

view full answer...

Answer 4

On the Lippert #LC119226, the slot in question is 1/4 inch wide by 3/8 of an inch deep, on the #RVLG-HDL it measure 1/4 inch wide by 7/16 of an inch deep. You can see these photos in the photo I've provided.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Dimensions of the Opening on Replacement Manual Override Crank # BD500203

Continue Researching