Replacement Disc Brake Rotor for Dexter 10K/12K Axle

Question

Question:

I need replacement rotor for 12k dexter axle approx diameter 1110 7/8 my understanding is I need part #070-006-01 but description on your website states 12 1/4inch for 10k axle, can please verify product dimensions/fitment? Thanks

asked by: Taylor

0

Expert Reply:

According to my research, the correct replacement rotor for your Dexter 12K Axle (Non-ABS) is the Replacement Rotor for Dexter Disc Brakes part # 070-006-01 which measures 11" in diameter. The Dexter 10K and 12K axles will both use the same rotor.

expert reply by: Conner L

0

Answer 1

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 2

The Replacement O-Ring for Dexter Axle 10K and 12K Disc Brakes part #010-062-00 install on the brake caliper guide bolts between the brake pads as shown in the photo below.

view full answer...

Answer 3

For Dexter 12k oil bath hubs we have the seal part #10-56 which would be exactly what you are looking for.

view full answer...

Answer 4

Attached is a photo of how the Replacement 11" Rotor for Dexter Disc Brakes #070-006-01 that you referenced fits with the hub. To replace your brake pads #BP04-395 you need to remove the bolts holding the old ones in place, take the cap off of…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 11

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 12

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

view full answer...

Replacement Disc Brake Rotor for Dexter 10K/12K Axle

Product Page this Question was Asked From

Continue Researching