Outer Tube Diameter of the Stromberg Carlson Replacement Foot Pad # 2500-3755G

Question

Question:

What is the tubes outer diameter? Thanks in advance.

asked by: Philip

0

Expert Reply:

The tube outer diameter for the Replacement Foot Pad # 2500-3755G is 1-3/4". I have attached a photo for you to reference.

A review video is also linked where this information is addressed as well.

expert reply by: Jon G

0

click to enlarge

Answer 1

You will need to choose a jack whose capacity exceeds the fully loaded and ready to tow tongue weight of your trailer. Typically trailer tongue weight is 10-15 percent of the weight of the trailer. This means that when loaded to maximum, your tongue…

view full answer...

Answer 2

The Replacement Foot for etrailer or Ram Electric Jacks #EJ-3520-FT has an inner diameter of about 1-1/2" and its outer diameter is 1-3/4" which is the measurement you'll need if you are looking for a replacement. This foot is designed…

view full answer...

Answer 3

I went out to my warehouse a pulled a few different jacks that I think will work for you. The Bulldog Round, A-Frame Jack, #BD1550101344, measures 14-1/2 inches from the bracket to the top of the jack, but you will lose an inch of lift with a 13 inch…

view full answer...

Answer 4

For your jack that features an inner tube diameter of just under 1-3/4 inches, we do have the Dutton-Lainson Steel Foot #DL22541 that should fit and work well. This removable steel foot is designed for jacks with a capacity up to 1,000 pounds and has…

view full answer...

Answer 5

The closest thing we have which may work is a jack foot for a Stromberg Carlson jack, and it has a 1-3/4" tube diameter: - Replacement Foot Pad for Stromberg Carlson Electric Trailer Jacks #2500-3755G This is otherwise similar, with a total…

view full answer...

Answer 6

The outer diameter of this tube is 1-3/4 inches, if that matches the diameter of your old foot, this should work well for you. A snapper pin like #2500-26 is typically used to hold the foot in place.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Outer Tube Diameter of the Stromberg Carlson Replacement Foot Pad # 2500-3755G

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching