Grease Coming Out of EZ Lube Trailer Spindle
Updated 06/27/2018 | Published 06/26/2018 >
Question:
Hello I was servicing my boat trailer bearings for the 1st time and I noticed as I was pumping grease in it was the old grease was coming out the back of the spindle and I just wanted to make sure this is ok? if it is ok I assume I should keep filling till I see new grease coming out of that hole..
asked by: Jay
Expert Reply:
There are only 3 ways that grease will come out on an EZ Lube axle.
1) You pump it in and it oozes out of the hole in the shaft to lubricate the bearings (normal operation). But you wouldn't see it because the hub/drum would be installed
2) It comes out the back of the hub meaning you blew a seal (seal needs to be replaced, use double lip seals)
3) It comes out where you are pumping it in because the hub/drum is full (if you see new grease then you are good to go)
When adding grease the hub/drum, bearings, everything, needs to be installed on the spindle. Adding grease would be the last step. You also have to make sure that any new grease you use is compatible with the old grease. If not and you do not clean away all of the old grease first, it can cause the grease to degrade quickly. I have included a link to our help article on grease for you.
Product Page this Question was Asked From
#84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Trailer Spindles
- EZ Lube Spindle
- With Flange
- L68149
- 1-3/4 Inch Diameter
- Round
- For 3500 lb Axle
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: trailer brake kits
- Search Results: 10 36 seal
- Search Results: trailer bearings races seals caps
- Search Results: trailer jack
- Article: 4 Reasons Not to Use RV Solar Power (And 4 Reasons You Should)
- Article: Trailer Wiring Diagrams
- Search Results: lug nuts
- Search Results: boat trailer hubs
- Search Results: boat trailer rims
- Shop: etrailer 12V Power RV Patio Awning - 20' Wide - 8' Projection - 4-Layer Vinyl - Black Fade
- Article: 4-Step Guide to Installing RV Solar Power
- Video: Ultimate Overview of the Kodiak Disc Brakes
- Shop: Grease Seals 10-36 - Double Lip - I.D. 2.250" / O.D. 3.376" - 5.2K to 8K Axles
- Shop: Kodiak Disc Brake Caliper - KodaGuard - 3,500 lbs to 6,000 lbs
- Shop: Kodiak Disc Brake Caliper - Dacromet - 3,500 lbs to 6,000 lbs
- Shop: Rich Solar RV Solar Charging Kit w/ 6 Panels - 12V - 1,200 Watts
- Shop: Dexter Bearing Kit - Bearings 15123/25580, Races 15245,25520, Seal 10-36
- Shop: Grease Seal 10-36 - Double Lip - I.D. 2.250" / O.D. 3.376" for 5.2K-7K Axles - Qty 1
- Video: Spindle Grease Seal Set for L44643 Inner Bearing and 1.980 Bearing Buddy Spec Review
- Q&A: Brake Fluid Leaking Around Master Cylinder Fill Cap On Titan Aero 6000 Surge Brake actuator
- Q&A: Can Different Marine Grease Be Mixed Together If They Have The Same Base
- Video: CE Smith Trailer Hub Assembly w/ Carrying Case for 2,700-lb Axles Spec Review
- Q&A: Installing Bearing Buddy Grease Seal Set # BB60005
- Q&A: Installing Bearing Buddys on EZ Lube Spindle
- Q&A: Troubleshooting Slight Amount of Grease Leaking from E-Z Lube Spindle
- Q&A: Will Bearing Buddy Fit on Trailer Axle With EZ Lube Spindles
- Q&A: Troubleshooting EZ Lube Initial Grease Leaking Out Rear Grease Seal
- Video: Timken Bearing Kit Installation - Enclosed Trailer
- Video: Timken Bearing Kit Step-By-Step Replacement - Utility Trailer
- Video: Review of Dexter Grease Cap Plug EZ Lube Grease Caps - DX89HR


