Can 4" Offset Ball for B&W Turnoverball Gooseneck be Used in Reverse?

Question

Question:

Can I use this in reverse to actually move my trailer 4 inches forward ?

asked by: Karl A

0

Expert Reply:

I spoke with a representative of B&W who told me that you should not use the 4" Offset Ball for B&W Turnoverball Gooseneck Trailer Hitches # BWGNXA4085 in reverse to move your trailer forward. The offset ball is only designed to be used as an extension to give you 4" of additional clearance and not the other way around.

expert reply by: Kyle S

0

Answer 1

A trailer light with 3 wires, like #RVSTL0060, that are black, white, and green generally the black wire is for running lights, green is for stop and turn signal, and white is for ground. If the old light on your trailer only used 2 wires, then it…

view full answer...

Answer 2

There are two options you can use for a bit of added height when using your B&W Turnoverball Underbed Gooseneck Hitch #BWGNRK1016. You can get an extra 1" by using the High-Rise Ball for B&W Turnoverball #BWGNXA2050. You can also use the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Can 4" Offset Ball for B&W Turnoverball Gooseneck be Used in Reverse?

Product Page this Question was Asked From

Continue Researching